Clutch

Minisport

Clutch

The mini clutch is one of the most unique clutch setups on ANY cars, rarely do everyday automotive parts suppliers understand or stock parts for your mini clutch. This clutch section is one of the most comprehensive on the net!...We not only stock the parts but we know trade tricks to get you the best clutch pedal possible (as we fit them as well).

Pricing:
Sort by:

Mini ring gear. thin type for inertia type starters (thick one is also available) - 22G2613

22G2613- RING GEAR THIN FOR INERTIA STARTERS (NOT PRE ENGAGED TYPES)

The thin ringer is for old type inertia type starters and used on lightened steel flywheel C-AEG619 and C-AEG421.

Originally fitted to automatic cars and old cast flywheels when lightened by various tuning shops in the 79s and 80s which is not recommended for competition

$109.05
($78.81 USD ) In stock

Mini master cylinder extension sleeve (suits all tin can and latest plastic) - BHA4661

BHA4661- MASTER CYLINDER EXTENSION SLEEVE

This age-old accessory screws onto the master cylinder in place of the cap, effectively increasing fluid capacity by about 20%. With the demise of the tall reservoir "S" master cylinder, this is the only way to regain that safety margin of a little more fluid!

$22.68
($16.39 USD ) In stock

Mini flywheel bolt for the A series engine (not A plus- verto) - 22A747

22A747- FLYWHEEL BOLT PRE VERTO

the bolt that holds the flywheel to the crank on cars with a diaphragm type clutch. Locked in place by 22A1155 locktab

$20.00
($14.45 USD ) In stock

Mini flywheel keyway for the A series engine (not verto- A plus) - 88G508

88G508- FLYWHEEL KEYWAY - PRE VERTO (MADE IN EN24T STEEL)

This flywheel locking plate is for pre verto diaphragm clutches.

$27.23
($19.68 USD ) In stock

Mini flywheel locktab - 22A1155

22A1155- FLYWHEEL BOLT LOCKTAB PRE VERTO

Flywheel bolt locktab for all diaphragm type clutch systems--The verto system had a flywheel bolt with built in locktab.

$13.59
($9.82 USD ) In stock

Primary gear C ring, a worn one can cause clutch shudder! - 22A319

22A319- PRIMARY GEAR C RING ON CRANK GENUINE

PRIMARY GEAR C WASHER it is better to use a genuine item if you are running a performance engine and you wish to shim the primary gear up perfectly. This fits against the 88G549 spacer backing ring.

$17.23
($12.45 USD ) In stock

MINI & MOKE PRIMARY GEAR BACKING RING - 88G549

88G549- MINI & MOKE PRIMARY GEAR BACKING RING

Spacer fits up against the primary gear on the crankshaft and held on by the "C" washer 22A319- both these parts wear as well as the gear.Only fits cranks from 1962 on with 1.5" tail width-NOT the earlier 1.3/8" tail size.0.164 plus or minus one thou.

$45.41
($32.82 USD ) In stock

Mini primary gear/seal removing tool - Tool 30

TOOL30- Mini primary gear/seal removing tool

This is the tool that removes the seal, so you can replace the clutch main seal and primary seal. it 'grips' on to the primary gear seal and then the bolt in the top forces the primary gear out.

$126.36
($91.33 USD ) In stock

Mini rover (Verto) clutch arm - DAM5355

DAM5355- CLUTCH LEVER ARM SHORT VERTO

Check the ball end for wear The late model Minis were converted over to a much smoother operating clutch setup. The 'verto' clutch as it is called also uses a different and much shorter arm in the flywheel housing.

$50.00
($36.14 USD ) In stock

Mini rover (verto) Clutch plunger - DAM5353MS

DAM5353MS- CLUTCH PLUNGER VERTO 82 ON (release bearing carrier)

The late model (rover) Minis were converted over to a much smoother operating clutch setup. The 'verto' clutch as it is called also uses a different plunger in the flywheel housing to hold the Clutch release bearing.

$50.00
($36.14 USD ) In stock

Mini rover (verto) imported thrust bearing - GRB239

GRB239- Verto clutch release bearing

If your late model Mini has a short (3" or so) clutch arm, you have a "Verto" clutch. This is your release (throw-out) bearing.

$31.82
($23.00 USD ) In stock

Mini rover (verto) flywheel bolt, built on locktab - DAM5922

FLYWHEEL BOLT ,VERTO TYPE CLUTCH 1982 on

Flywheel bolt with built in locktab for Verto type flywheels only

$20.00
($14.45 USD ) In stock

Mini flywheel locating plate (A+) verto clutch - DAM5923

DAM5923- FLYWHEEL KEYWAY LOCATING PLATE A+

Mini flywheel locating plate (A+) verto clutch.

$53.64
($38.76 USD ) In stock

Mini clutch sleeve (A+) sleeve that covers the flywheel bolt. - AHU1564

AHU1564-CLUTCH SLEEVE A+

Sleeve that covers the flywheel bolt on verto clutches for the release bearing

Note--early 58mm internal diameter sleeves had a plastic anti rattle sleeve which is no longer available but this later type is smaller in diameter and therefore does not require the sleeve

$63.59
($45.96 USD ) In stock

MINI, STARTER MOTOR RING GEAR 129T VERTO PRE-ENG - PSF10003

PSF10003- MINI, STARTER MOTOR RING GEAR 129T VERTO PRE-ENG

Ring gear for all cars fitted with the pre-engaged starter on Verto flywheels from about 1984 on. Can be used when changing from interia starter to an 11 tooth pre-engaged starter. If you have 11 teeth on your bendix then this is the one you need.

$81.77
($59.10 USD ) In stock