Minisport

Driveline

Pricing:
Sort by:

Mini rear hub (all models)- reconditioned - REAR_HUB

Rear Hub (all models)

This rear hub assembly to suit any model mini- this has been pulled down, cleaned inspected and ready for you to put back together.

$50.00
($37.28 USD ) In stock

Mini rear hub (all models) *Brand new* - RLH10021

21A2023- Mini rear hub (all models 1959-1999) *Brand new*

Classic mini rear hub (all models 1959 to 1999) *Brand new*

$68.18
($50.84 USD ) In stock

KAD Alloy Rear Hubs (pair) - 1012270

1012270- KAD Alloy Rear Hubs (pair)

KAD Billet Alloy Rear Hub Set. Half the weight of the standard steel item. Supplied as a pair complete with wheel studs and wheel bearings.

$450.00
($335.55 USD ) In stock

Mini 3/8 pin rear stub axles (pair left and right) needed when converting hydro to spax kit/rubber - stub_axle

Mini rear stub axles

These are needed to allow the rear shockers on the spax kit to fit hyro cars as the pins are not threaded and are not 3/8 in size.

These are included in the 'convert from hydro to rubber kit' please note that colour can change (some are black)

$154.55
($115.24 USD ) In stock

Mini rear hub nut (RIGHT HAND REAR)- right hand thread - NL610041

NL610041- REAR HUB CASTLE NUT R/H

Rear hub nuts on the mini are sided as the threads are different. this is for the right hand rear and is usual right hand thread to tighten. See FNN2410 for left hand nut

$12.68
($9.46 USD ) In stock

Mini rear hub nut (LEFT HAND REAR)- left hand thread - FNN2410

FNN2410- REAR HUB NUT LEFT HAND

Rear hub nuts on the mini are sided as the threads are different. this is for the LEFT hand rear.This has a left handed thread. See NL611041 for right hand nut

$12.68
($9.46 USD ) In stock

Mini rear hub nut washer (goes between the nut and the bearing) - BTA672

BTA672- Mini rear hub nut washer (goes between the nut and the bearing)

Mini rear hub nut washer (goes between the nut and the bearing), please note that the taper goes towards the bearing

$8.14
($6.07 USD ) In stock

Mini rear hub grease cap - ATB4098

ATB4098- HUB REAR GREASE CAP

fits the rear hub of every mini to protect the bearings grease from debris but this metal cap always seems to get damaged on 10" wheel cars or when you change the bearings-make sure yours are in place.

$20.00
($14.91 USD ) In stock

Mini drive shaft U bolt (comes with nuts) - 22A132

22A132- Mini drive shaft U bolt (comes with nuts)

For use on drive shaft couplings where they have the rubber cross or needle roller conversion. This is for 1x replacement drive shaft U bolt (comes with nuts)

$4.50
($3.36 USD ) In stock

Drive shaft rubber uni joint - GCD101

GCD101- DRIVESHAFT RUBBER COUPLING KIT single

The very early Minis used the rubber U-joint drive couplings to eliminate harshness being transmitted to the passenger compartment, comes with U bolts and nuts.

$63.59 $50.00
($37.28 USD ) In stock

Mini pair of nylon universal joint (replaces rubber crosses) - QL5000 (PAIR)

QL5000PR- Pair of mini nylon universal joints (replaces rubber cross)

The early Minis used the rubber U-joint drive couplings to eliminate harshness from being transmitted to the passenger compartment. Over the years the rubber will separate from the metal sleeves and allow the driveshaft to rotate out of concentricity. Not only can this cause vibration, but it can also allow it to hit either the tranny case or more often, the exhaust pipe. The rubber coupling has an alternative, these are superior nylon cups with needle bearings. One kit (as shown) comes complete with new 2x Joints, set of 8 U-bolts & 16 nuts.

$159.09 $150.00
($111.85 USD ) In stock

Mini Cooper S and Auto inner uni joint assembly - GUJ101

GUJ101- Mini Cooper S/auto hardy Spicer inner universal joint

This joint is for the hardy Spicer that was fitted to the Cooper S model (and auto) it comes with circlip as well

$27.23 $19.95
($14.88 USD ) In stock

Mini hardy spicer output shaft bolt sold single(suit cooper S and Auto) - 22A1139 - 22A1139

22A1139- OUTPUT SHAFT BOLT "S"

There are 4 of these to each output flange to which the Hardy Spicer joint bolts as used on cooper 'S' and automatics 

$9.05
($6.74 USD ) In stock

PHILIDAS NUT FOR 22A1139 OUTPUT SHAFT BOLT - GFK3431

GFK3431- PHILIDAS NUT FOR 22A1139 OUTPUT SHAFT BOLT

Special height locking type nut for the hardy spicer joints on Cooper S and automatics to fit the 22A1139 bolt. Sorry about the price but only available from Philidas Ltd.

$3.59
($2.68 USD ) In stock

Mini hardy spicer output shaft collett. (4 req per car, 2 per side) - 88G493

88G493- HARDY SPICER OUTPUT SHAFT COLLETT (SOLD SINGLE)

Only fitted to vehicles with hardy spicer output shafts (Cooper S and autos). Two collets are fitted in the output shaft in the gearbox and located behind the rubber seal.

$20.00
($14.91 USD ) In stock