Minisport

Driveline

Pricing:
Sort by:

OIL SEAL FOR HARDY SPICER OUTPUT SHAFT BOLT - 22A1566

22A1566- OIL SEAL FOR HARDY SPICER OUTPUT SHAFT BOLT

If you have Hardy Spicer output shafts as fitted to Cooper "S" and automatic minis these seals fit behind the output shaft to prevent oil leaking through the centre bolt area. They are a special neoprene type of rubber to prevent heat breaking them down.

$9.05
($6.75 USD ) In stock

SPRING WASHER FOR HARDY SPICER BOLT - 22A1567

22A1567- SPRING WASHER FOR HARDY SPICER BOLT

If you have Hardy Spicer output shafts as fitted to Cooper "S", automatic minis & clubman GT; this is the large spring washer that sits inbetween the hardy spicer bolt and the flat washer. (as circled in the image) *BOLT AND WASHER ARE NOT INCLUDED*

$2.23
($1.66 USD ) In stock

Mini hardy spicer complete coupling new assembly (sold per single unit) - 27H7880

27H7880- HARDY SPICER COUPLING ASSEMBLY

Hardy-Spicer coupling was fitted to the Cooper "S" and all automatic varieties pre Pot joint (inboard cv joint) This U-joint assembly slides onto the driveshaft and bolts to the Cooper S output shaft flange.

$268.18
($200.17 USD ) In stock

Mini Disc brake CV joint nut (non genuine, 34mm head) - BTA249MS

BTA249MS- FRONT HUB NUT METRIC 34MM,LARGE CV TYPE

Nut for DISC brake CV joint, metric 34mm- for original 1-5/16 see BTA249

$6.36
($4.75 USD )

Mini Disc brake CV joint nut, (genuine, 1-5/16" head) - BTA249

BTA249- FRONT HUB NUT ORIGINAL 1.5/16"AF Large/DISC CV joint (33.3MM)

As fitted to disc brake front end minis, this CV nut is original 1.5/16"AF size nut this is about 33.3mm

$13.59
($10.14 USD ) In stock

Mini Disc brake CV joint cone washer, fits into flange - FAM9270

FAM9270- HUB NUT CONE WASHER FOR CV JOINT

The large sintered, cone washer that goes behind the hub nut on the CV joint. Fitted on all minis with the large type CV joint when disc brakes are fitted

$9.05
($6.75 USD ) In stock

SPLIT PIN FOR DRUM BRAKE CV JOINT & ALSO DOES REAR HUB NUT - GHF511 (split pin)

GHF511SPLIT PIN FOR GCV1105 CV JOINT & ALSO DOES REAR HUB NUT 

Correct size split pin for the early smaller type CV joint (GCV1105) fitted to drum brake cars and cooper small discs (also fits the rear hub nut)

$0.91
($0.68 USD ) In stock

SPLIT PIN FOR OUTER CV JOINT (DISC BRAKES ONLY) - GHF510 (split pin)

GHF510- SPLIT PIN FOR OUTER CV JOINT (DISC BRAKES ONLY)

Split pin for the larger size CV joint as fitted to disc brakes. This pin is usually supplied in our normal stock bearing kits. Sold individually

$1.00
($0.75 USD ) In stock

MINI & MOKE PLUNGE JOINT BALL FOR INBOARD CV. - BALL

BALL- MINI & MOKE PLUNGE JOINT BALL FOR INBOARD CV.

This ball fits all pot joints (inner C.V.) as fitted from 74 on. You will need 6 per joint. SIZE: 21/32 (16.6688MM)

$4.50
($3.36 USD ) In stock

Mini R/H pot joint shaft (upgraded in EN24)- Long shaft - MS1246

MS1246- Mini R/H pot joint shaft (upgraded in EN24)- Longer shaft

Drive shaft to suit Pot joint (inner CV) 'long driveshaft' Upgraded in EN24 steel 

$177.27
($132.32 USD ) In stock

Mini L/H pot joint shaft (upgraded in EN24)- Short shaft - MS1247

MS1247- Mini L/H pot joint shaft (upgraded in EN24)- Shorter shaft

Drive shaft to suit Pot joint (inner CV) Short driveshaft' Upgraded in EN24 steel

$177.27
($132.32 USD ) In stock

MINI DRIVESHAFT "S" LONG R/H - 27H4775

27H4775- MINI DRIVESHAFT "S" LONG R/H

HEAVY DUTY AXLES! The Mini drive shaft or half axles are different from side to side. This, the right side one is the longer of the two. 

$177.27
($132.32 USD ) In stock

MINI DRIVESHAFT "S" SHORT L/H - 27H4776

27H4776- MINI DRIVESHAFT "S" SHORT L/H

HEAVY DUTY AXLES! The Mini drive shaft or half axles are different from side to side. This, the left side one is the shorter of the two. 

$177.27
($132.32 USD ) In stock

MINI PAIR OF MONTE DRIVESHAFTS - REMOTE TYPE - C-BTA1267

C-BTA1267- MINI PAIR OF MONTE DRIVESHAFTS - REMOTE TYPE

Special Tuning hit upon this idea to get over the driveshafts breaking on their rally cars. Do away with the large circlip groove where it broke and weld a spacer on the shaft to locate the CV joint in position. The works department also reduced the steering lock to eradicate over stressing of the shaft on full lock. These were for the remote type box or original Cooper S variants.

$268.18
($200.17 USD ) In stock

MINI & MOKE COMPETITION DRIVESHAFTS (TARMAC) - POT JOINT TYPE - C-BTA1264

C-BTA1264- DRIVESHAFTS POTJOINT(TARMAC)COMPETITION TYPE

Competition driveshafts made in steel for use with inboard pot joints. Upgraded to stop ends twisting off.

$450.00
($335.89 USD ) In stock