Minisport

New Products

This is for new mini parts that we get in stock, keep your eye on this section of the website daily as we add to it almost everyday, its just one way minisport is trying to keep your mini looking its best!

Pricing:
Sort by:

MINI PARCEL SHELF REAR PANEL - 14A6564

14A6564- MINI PARCEL SHELF REAR PANEL

This panel now comes with cut out holes only- 2 large and 2 small holes which were used for Rover fitted speakers.

$250.00
($188.66 USD ) In stock

MINI WING INNER VENT PANEL RADIATOR SLATS 59 TO 89 - HMP441023

HMP441023- MINI WING INNER VENT PANEL RADIATOR SLATS 59 TO 89

Genuine Left hand front inner wing repair section with the radiator slats only -does not include the radiator shroud panel which is available seperately as 14A6498

$118.14
($89.15 USD ) In stock

MINI MK1 COOPER S METAL BACKING, BRACKETS & AFFIXING PARTS - 14A9904 & 24A0053K

14A9904 & 24A0053K- MK1 MINI COOPER S METAL BACKING, BRACKETS & AFFIXING PARTS

This is the MK1 Cooper S dash surround metal backings and attaching plates- complete with all affixing screws and spacers to fit to your MK1 Cooper S restoration

$268.18
($202.39 USD ) In stock

MINI FULL FLOOR PANEL WITH CROSS MEMBER, SILLS & TOE BOARD MK1&2 - 24A2615

24A2615- MINI FULL FLOOR PANEL WITH CROSS MEMBER, SILLS & HEEL BOARD MK1&2

Complete non genuine floor pan assemby with crossmember, 2x sill's, heel board. This floor is 4 vent sill with round tunnel only for the remote type gear change vehicles only *EXTRA SHIPPING WILL APPLY*

$1813.64 $1722.73
($1300.07 USD ) In stock

MINI MK1/2 REAR QUARTER PANEL- R/H MK1/2 - MS17R

MS17R- MINI MK1/2 REAR QUARTER PANEL- R/H MK1/2

Rear quarter panel to suit the MK1/2 round nose minis in Australia & the UK- Please note that these are a little bit different to the Australian Leyland rear quarter panels and very different to the UK internal hinge rear quarter panels MK3 onwards.

$268.18
($202.39 USD ) In stock

MINI MK1/2 REAR QUARTER PANEL- L/H MK1/2 - MS17L

MS17L- MINI MK1/2 REAR QUARTER PANEL- L/H MK1/2

Rear quarter panel to suit the MK1/2 round nose minis in Australia & the UK- Please note that these are a little bit different to the Australian Leyland rear quarter panels and very different to the UK internal hinge rear quarter panels MK3 onwards.

$268.18
($202.39 USD ) In stock

MINI CLUBMAN PLASTIC CLIP FOR BONNET PROP (AND SUNVISORS ON 64/65 MINIS) - GFK7344

GFK7344- CLUBMAN PLASTIC CLIP FOR BONNET PROP (AND SUNVISORS ON 64/65 MINIS)

Plastic clip for sunvisor 1964-5 and Australian clubman bonnet props (& early UK cars) ,was GHF1120 and ADA4370. the side clip on these models was ADA4484. This set up was used with first plastic mirrrors and black rubber sucker 24A1535

$6.32
($4.77 USD ) In stock

Mini seam cover mirror (Round)- clip on type- Right hand side only - MIRROR01RND

MIRROR01RND- Mini seam cover mirror (Round)- clip on type

Mini seam cover mirror (Round)- clip on type. This mirror attaches to the seam cover and requires no drilling in your door. These are a great alternative to the conventional door mirror. **See description for picture of it attached/in situ**

$45.41
($34.27 USD ) In stock

MINI BONNET LOCK GUIDE PLATE (ROUND NOSE MINI ONLY) - AAM1223

AAM1223- MINI BONNET LOCK GUIDE PLATE (ROUND NOSE MINI ONLY)

This is the original bonnet slam catch- This guide plate for the bonnet locking pin.

$14.50
($10.94 USD )

Out of Stock

MINI RADIATOR LOWER BRACKET- SUIT COOPER "S" ONLY - 12A293

12A293- MINI RADIATOR LOWER BRACKET- SUIT COOPER "S" ONLY

When the "S" motor was introduced to the public a two piece vibration damper was also introduced. This is reputed to be the best system for vibration control for the Mini motor. The only problem with it was that is was bigger and wider than the other version. And in fact the first of the motors had no damper at all! With the close quarters of the Mini engine compartment the bottom radiator mounting became a problem and thus this special lower bracket with a bend in was introduced for ARA2770/RADCOWL002 radiator cowling. If you are upgrading you might need this simple piece that fits to 12A361 bracket!

$31.77
($23.98 USD ) In stock

MINI MK3 ON (ROVER) DOOR ASSEMBLY BARE LESS HINGES R/H (PRE-CRASHBAR TYPE) - BMP326/BMP306MS

BMP326/BMP306MS- MINI (ROVER) MK3ON DOOR ASSEMBLY BARE LESS HINGES R/H (PRE-CRASHBAR TYPE)

Genuine R/H door without crash bar which only later cars had fitted. This door also has no hinges.*EXTRA POST WILL APPLY*

$1177.27
($888.44 USD ) In stock

MINI MK3 ON (ROVER) DOOR ASSEMBLY BARE LESS HINGES L/H (PRE-CRASHBAR TYPE) - BMP327/BMP307MS

BMP327/BMP307MS- MINI (ROVER) MK3ON DOOR ASSEMBLY BARE LESS HINGES L/H (PRE-CRASHBAR TYPE)

Genuine L/H door without crash bar which only later cars had fitted. This door also has no hinges. *EXTRA POST WILL APPLY*

$1177.27
($888.44 USD ) In stock

MINI & MOKE GOLD 'LUCAS' SPORTS COIL- 12V - DLB105

DLB105- MINI & MOKE GOLD LUCAS SPORTS COIL- 12V

This is A MUST for anyone restoring an engine bay or that wants a sports coil, it not only looks fantastic but also really performs. Coil resistance is: 3.5ohms on the primary, 10.6k ohms on the secondary- LUCAS TYPE

$63.59
($47.99 USD ) In stock

MINI & MOKE PAIR OF RETRO P700 HEADLAMPS (WITH H4'S AND PARKERS) - P700

P700- MINI & MOKE PAIR OF RETRO P700 HEADLAMPS (WITH H4'S AND PARKERS)

These are a replica headlamp assembly of the original P700 headlamps as fitted in the 60's. These have been upgraded to the H4 replacement type globes and parker lamps. These headlamps are made for pre ADR cars.

$177.27
($133.78 USD ) In stock

MINI WORKS LAMP BAR S/STEEL PLUS FITTINGS - C-AJJ3329

MSA1101- MINI WORKS LAMP BAR S/STEEL PLUS FITTINGS

Copy of the original heavy duty works lamp bar with all fittings but now in stainless steel for longevity.This type was used on LBL66D on the 1967 MONTE CARLO RALLY. Consists of a central support bracket and 2 end supports to keep the lamps stable under any conditions-this reduces the vibration which would make the extra lights ineffective(other bars offered by competitors that straddle the 2 small single brackets are useless). A black version of this is also available as MSA1101. These cannot be fitted with front overiders and the bottom moulding of the grille slat will need relieving upwards about 25mm and the width of the 2 outer brackets for fitment. This is now a straight bolt on part with our new 2014 re-design for current genuine and non genuine front panels, but the lower part of the grille must be modified. They might entail some cutting of early original front panels and MK1 grille as per original works cars so please do not think this is a bolt on item

 

$222.73
($168.08 USD ) In stock