Minisport

Thermostat housings & thermostats

Pricing:
Sort by:

MINI & MOKE THERMOSTAT HOUSING GASKET - AYA121/GTG101MS

AYA121/GTG101MS- MINI & MOKE THERMOSTAT HOUSING GASKET

Forget all the universal shape gaskets available - this is the original correct shape thermostat housing gasket made out of thick gasket paper. Fits all models.

$2.00 $1.77
($1.34 USD ) In stock

Mini & Moke forward facing thermostat housing - 12G103

12G103- Mini & Moke forward facing thermostat housing

As used on minis and mokes from 1959 until around 1976/77 when they changed to the rear facing setup.

$24.50 $20.86
($15.74 USD ) In stock

Mini forward facing thermostat housing, with temp adaptor - 12A408

12A408- Thermostat housing with temp adaptor.

This thermostat housing is fitted with an adaptor for the temp sensor, this allows either use of both mechanical and electric temp gauges, or in the early cars use of electric gauge to be fitted.

$54.50
($41.13 USD ) In stock

Mini/moke 'late model' small bore (1000cc) rear facing thermostat housing *BACK IN STOCK* - CAM4044

CAM4044- 1000cc rear facing thermostat housing

These where fitted to late model 76>81 mokes and minis, the outlet faces the firewall (not the front like on earlier cars) 1000cc

$62.73
($47.34 USD ) In stock

Mini/moke 'late model' 1275 rear facing thermostat housing - AYG2388

AYG2388- 1275 rear facing thermostat housing

These where fitted to late model 76>81 mokes and minis, the outlet faces the firewall (not the front like on earlier cars)

$62.73 $53.59
($40.44 USD ) In stock

Mini 'SPI/CARB' THERMOSTAT SANDWICH PLATE WITH OUTLET - PEG10002

PEG10002 - Mini 'SPI' THERMOSTAT SANDWICH PLATE WITH OUTLET

1992 TO 1996 SANDWICH PLATE. SPI AND CARB MINIS. HAS TAPPED HOLE FOR RAD BRACKET STUD. NO SENDER HOLES. SPI MINIS USE WITH 12G103 TOP HOUSING.

$81.77
($61.71 USD ) In stock

Mini 'MPI' thermostat housing sandwich plate - PEG100030

PEG100030 - THERMOSTAT SANDWICH PLATE ELBOW TWIN POINTS ONLY

MPI SANDWICH PLATE. NO HOLE FOR RAD BRACKET STUD. SAME CASTING AS ALL OTHERS BUT HAS LARGE DRILLED HOLE IN SIDE FOR TRANSMITTER

$81.77
($61.71 USD ) In stock

MINI ROVER THERMOSTAT HOUSING SINGLE POINT - PEQ100690

PEQ100690- MINI ROVER THERMOSTAT HOUSING SINGLE POINT

Fitted on very late single points,autos and Japanese spec cars where the outlet was moved 45 degrees further away from the engine compared to the old original 12G103

$89.09
($67.23 USD ) In stock

MINI ROVER/METRO THERMOSTAT HOUSING LARGE BORE - ALL CARB COOPERS - PEQ10019

PEQ10019- MINI ROVER/METRO THERMOSTAT HOUSING LARGE BORE - ALL CARB COOPERS

Larger bore thermostat housing, approx 32MM wide(1.250")and has a small outlet pipe which is blanked off (not drilled out). This same housing was used on Metros but the blanked off outlet was drilled out for water to go to the expansion tank. Uses GRH1140 hose for PEQ10019 housing which is large bore one end and correct size at other end to fit the standard radiator size outlet. This larger bore housing is a useful upgrade in hot climate countries.

$89.09
($67.23 USD ) In stock

74 degree thermostat (suit warmer conditions) - GTS102

GTS102- Mini thermostat (74 degrees CELCIUS) 

Thermostat for Australian Conditions 74 degrees (suit warmer conditions)

$10.91
($8.23 USD ) In stock

Mini thermostat blanking sleeve, A MUST when removing thermostat - 11G176

11G176- THERMOSTAT BLANKING SLEEVE

Removal of the thermostat helps to reduce engine temperature; however a thermostat blanking sleeve should be fitted to maintain correct coolant circulation to the entire head.

$27.23
($20.55 USD ) In stock

MINI & MOKE 5/16" THERMOSTAT HOUSING STUD (4.5CM) - CHS2515

CHS2515- STUD FOR THERMOSTAT HOUSING WITHOUT SANDWICH PLATE (5/16")

Probably the most changed stud on the mini? This is the length used on every A series engine until the introduction of the sandwich plate when longer ones were replied. 5/16"unc and unf at nut end,this bolt is about 4.5cm long about 3.5cm from the bottom of the UNC thread

$4.50
($3.40 USD ) In stock

MINI & MOKE 5/16" THERMOSTAT HOUSING STAINLESS STEEL STUD AND NUT KIT - C-STR281

C-STR281- MINI & MOKE THERMOSTAT HOUSING STAINLESS STEEL STUD AND NUT KIT

Stainless steel Thermostat housing stud kit for the single tier type thermostat housing. Quantity required one kit per car.

$30.00
($22.64 USD ) In stock