Minisport

7.0" COOPER BRAKE PARTS

Pricing:
Sort by:

MINI COOPER (7" TYPE) BRAKE CALIPER PISTON (STAINLESS STEEL) 997/998 (1.618 DIA) - 17H7913

Early mini cooper they had 7" disc brakes fitted (unlike the 7.5" cooper S brake) This is a replacement (Stainless steel) brake caliper piston to suit both the 997 & the 998 cooper brakes. The piston is 1.618" of an inch diameter. Rebuild kit is GRK5009

$36.32
($26.55 USD ) In stock

MINI COOPER 7.0" (NOT S) CALIPER SEAL KIT - GRK5009

Genuine AP lockheed seal Rebuild kit for Cooper 997/998cc brake calipers. When it comes to safety critical parts only fit the original suppliers parts as repair kits.The kit includes all the seals needed to do both pistons in one caliper.

$15.41
($11.26 USD ) In stock

MINI & MOKE CALIPER BRIDGE SEAL- 7.0" & 7.5" CALIPER TYPE - 17H8764

This seal goes in between the caliper halves; it allows the brake fluid to transfer between pistons. A must for any caliper overhaul.

$10.00
($7.31 USD ) In stock

MINI & MOKE BLEED NIPPLE 3/8 UNF THREAD - 3H2428

Bleed nipple for 7.0" & 7.5" calipers. Also does the front wheel cylinders on twin leading shoe type set ups, this is where you have 2 cylinders per hub as single laeding type which had one cylinder only per hub. These are 3/8UNF thread

$2.68
($1.96 USD ) In stock

MINI & MOKE BLEED NIPPLE DUST COVER CAP - STC1913

This is the little dust cover cap that stops dirt and road grime getting into the brake bleeder valve. These fit bot the front 3H2428 front bleed nipples and the 513118A rear bleed nipples. Open advert for more images of these fitted on the nipple(s).

$2.00
($1.46 USD ) In stock

Mini 7.0" cooper brake pads, original (not S) - GBP102AF

These are the original cooper (7") pads but if you have the very early small pad type as per 997cc cooper get the calipers machined out to accept this pad as the small type GBP101 or BD20 is now so scarce and have not been made for some 10-15 years. fits all 998cc cooper with 7" disc width

$63.59
($46.48 USD ) In stock

PAIR OF SPLIT PINS FOR COOPER AND S CALIPER PAD TO CALIPER (SOLD AS A PAIR) - PS610241 (X2)

PS610241 X2- COOPER AND S CALIPER PAD PAIR OF SPLIT PINS

Correct size and length brake pad pin for the caliper using 7.5" disc size as fitted to Cooper S and 1275GT. 4 required for 1 car (YOU WILL NEED TWO PAIRS), also fits cooper 7" calipers.

$3.18
($2.33 USD ) In stock

MINI & MOKE BRAKE CALIPER RETAINING HT BOLT 1.5/16"LONG - 53K1048

53K1048- MINI & MOKE BRAKE CALIPER RETAINING HT BOLT 1.5/16"LONG

High tensile 3/8" bolt 1.3125" long to hold the standard calipers to the hub on disc brake models. Correct length shank and material. 

$3.14
($2.29 USD ) In stock

MINI 7.0" BRAKE DISC COOPER 997/998- NOT COOPER S - BTA193

BTA193- Mini cooper (NOT S, S are 7.5) Brake rotors. *PAIR*

THE ORIGINAL 7" COOPER DISC AVAILABLE IN BETTER GRADE G260 MATERIAL FITTED WITH WHEEL STUDS, Only sold in pairs.

$227.27
($166.13 USD ) In stock

MINI & MOKE FRONT DISC HUB- R/H - FAM2390

FAM2390- HUB FRONT R/H BTA186 COOPER & ALL DISC BRAKE MINIS

Call it a hub, bearing carrier, upright or swivel pin; on the Mini it's all the same thing. You'll need these (FAM2391=left, FAM2390=right) new hubs if you are converting to disc, or if your old hubs will no longer support the bearings properly.

$177.27 $131.82
($96.35 USD ) In stock

MINI & MOKE FRONT DISC HUB- L/H - FAM2391

FAM2391- HUB FRONT L/H BTA187 COOPER & ALL DISC BRAKE MINIS

Call it a hub, bearing carrier, upright or swivel pin; on the Mini it's all the same thing. You'll need these (FAM2391=left, FAM2390=right) new hubs if you are converting to disc, or if your old hubs will no longer support the bearings properly. All new and ready to use. Either replace your old one or start a kit to convert to disc.

$177.27 $131.82
($96.35 USD ) In stock

MINI & MOKE FRONT DISC HUB KIT- LIGHTWEIGHT ALLOY - FAM2390AKIT

Mini & Moke lightweight alloy swivel hubs in kit form to suit all models with disc type. 7075 aircraft grade high specification aluminium billet, then hard anodised. These specially designed swivel hubs are not only strong and durable but over 1kg lighter than the standard cast swivel hub!

$1268.18
($926.98 USD ) In stock

MINI & MOKE FRONT BRAKE RUBBER HOSE- DISC TYPE - GBH249

This is a mini or moke front rubber/flex brake hose. This is the shorter hose as fitted to disc brake model cars. The nut, washer and copper washer are also available to buy. Normal practise is to replace both hoses at the same time- This will avoid any brake 'pulling'.

$13.59
($9.93 USD ) In stock

MINI & MOKE FRONT BRAKE RUBBER HOSE KIT- DISC TYPE - GBH249KIT

This is a mini or moke front rubber/flex brake hose kit. This is the shorter hose as fitted to disc brake model cars.  This kit includes the hose, nut, washer and copper washer. Normal practise is to replace both hoses at the same time- This will avoid any brake 'pulling'.

$21.68
($15.85 USD ) In stock

BOOT CABLE COVER / FRONT DISC / RADIUS ARM SHROUD SCREW/ SCREW FOR BOOT LID WIRES - SE910161

SE910161- BOOT CABLE COVER / FRONT DISC / RADIUS ARM SHROUD SCREW/ SCREW FOR BOOT LID WIRES

This screw is used to hold together the 2 halves of the disc shields on all mini front discs. Also used to retain the boot lid cable to the bootlid.

$0.91
($0.66 USD ) In stock