Minisport

Camshafts and accessories

Pricing:
Sort by:

Mini camshaft locktab - 2A759

2A759- CAMSHAFT GEAR LOCKTAB

 If you are replacing your timing chain or just doing routine maintenance a new lock-tab is sure to come in handy!

$2.27
($1.60 USD ) In stock

Mini camshaft thrust plate (all sizes) - AHU2379

AHU2379- Camshaft thrust washer

Goes behind the camshaft pulley in the timing chain area, make sure yours isn't flogged out! (all sizes)

$27.23
($19.19 USD ) In stock

MINI CAMSHAFT RETAINING NUT - 6K629

6K629- MINI CAMSHAFT RETAINING NUT

Special flat nut (1-5/16" AF) for camshafts, uses 2A759 locktab

$11.77
($8.30 USD ) In stock

Cam-shaft dialer, suit all cams, "Kent" brand- C-AJP337 - C-AJP337

C-AJP337- MINI CAMSHAFT DIAL GUAGE 360 DEGREE

A vital aid for accurate valve timing this disc is a 360 degree protractor disc made by kent cams. This is a valve dial in gauge, it allows you to precisely get TDC and adjust your cam timing accordingly

 

$27.23
($19.19 USD ) In stock

MINI CAMSHAFT BEARING- 850cc - 1C4096

1C4096- MINI CAMSHAFT BEARING- 850cc

The 850cc ran a single cam bearing on the engine. If you have 3 then you might have one of the real late engines.

$31.77 $27.23
($19.19 USD ) In stock

MINI & MOKE CAMSHAFT BEARING SET- 998 & 1100cc - VP956/CSB604

VP956/CSB604- MINI & MOKE CAMSHAFT BEARING SET- 998 & 1100

This is a std cam bearing set for a 998 or 1098 engine, you will require a cam bearing installer to fit (or see an engine builder) 1275 engines are not the same, see VP989/CSB609. 850cc engines had a single cam bearing (see 1C4096 STD)

$31.77 $27.23
($19.19 USD ) In stock

MINI & MOKE CAMSHAFT BEARING SET- 1275cc - VP989/CSB609

VP989/AEC3063- MINI & MOKE CAMSHAFT BEARING SET- 1275cc

This is a std cam bearing set for a 1275 engine (note that small bore engines are not the same)

$31.77 $27.23
($19.19 USD ) In stock

MINI & MOKE KENT CAMSHAFT 266- FAST ROAD - MDM266

MDM266- CAMSHAFT MEGADYNE 266- FAST ROAD- A PLUS SLOT DRIVE

Brilliant all round performance road cam. Smooth idle, pulls from around 1,200 RPM. Small gain in low end, big increase in med and top end. Unbeatable for genuine fast road use. Rev band 1,200 to 6,500/7,000 rpm. 

$400.00
($281.91 USD ) In stock

MINI & MOKE KENT CAMSHAFT 276- FAST ROAD/RALLY - MDM276

MDM276- MINI & MOKE KENT CAMSHAFT 276- FAST ROAD/RALLY- A PLUS SLOT DRIVE

Slightly lumpy at idle, especially in small bore units. Strong mid and top end power. Rev band 1,500 - 7,000 rpm

$400.00
($281.91 USD ) In stock

MINI & MOKE KENT CAMSHAFT 276 KIT- FAST ROAD/RALLY - MDM276KIT

MDM276- MINI & MOKE KENT CAMSHAFT 276 KIT- FAST ROAD/RALLY

Slightly lumpy at idle, especially in small bore units. Strong mid and top end power. Rev band 1,500 - 7,000 rpm. Can be fitted in both small bore or 1275 engines, you will just need the correct oil pump. MD276 A plus cam with cam followers, valve springs and initial start up oil.

$522.73
($368.41 USD ) In stock

MINI & MOKE KENT CAMSHAFT 286- RALLY/RACE - MDM286

MD286- MINI & MOKE KENT CAMSHAFT 286- RALLY/RACE

Hottest road usable cam. Not a good traffic cam. Lumpy idle. Not very suitable for small bore units unless fully prepared with big valve head. Very strong mid and top end power. Rev range 2,000 - 7,500 rpm.

$422.73
($297.93 USD ) In stock

MINI & MOKE KENT CAMSHAFT 286- RACE- SCATTER PATTERN - MDM286SP

MD286SPM- CAMSHAFT 286 SCATTER CAM -SLOT DRIVE- 1275cc

This is possibly the ultimate type of race camshaft profiles of over 300 degrees of duration. If you've done your reading, then you know that "Scatter Pattern" cams are designed specifically for the peculiarities of the A-Series engine with it's five-port head.  Power band is 2000-7500.

$513.64
($362.00 USD ) In stock

MINI & MOKE KENT CAMSHAFT 296- RACE- SCATTER PATTERN - MDM296SP

MD296SPM- MINI & MOKE KENT CAMSHAFT 296- RACE- SCATTER PATTERN

This is possibly the ultimate type of race camshaft profiles of over 300 degrees of duration. If you've done your reading, then you know that "Scatter Pattern" cams are designed specifically for the peculiarities of the A-Series engine with it's five-port head. By optimizing lobe centers and phasing for each cylinder, improvements have been made in torque and bottom end power. The result is much better drivability in a very high performance cam. These Kent cams are reprofiled and sold outright, no exchange.

$513.64
($362.00 USD ) In stock

MINI & MOKE KENT CAMSHAFT 310- FULL RACE - MD310SPM

MD310SPM- MINI & MOKE KENT CAMSHAFT 310- FULL RACE

Needs fully prepared engine for good results - full race cam in A plus drive with power band from 4000-8500 with cam lift of .340

$513.64
($362.00 USD ) In stock

OIL PUMP- 850/998/1098- PIN DRIVE - GLP142

GLP142- 850/998/1100 oil pump, pin drive

Oil pump used on all all 850/1000/1100 (unless it is A plus in that case contact us for a AHU1050)

$60.00 $36.32
($25.60 USD ) In stock