Minisport

4 SYNCHRO PARTS & BEARINGS- PRE A+ (Up to 1979) with 14MM Nose Mainshaft

Pricing:
Sort by:

MINI & MOKE 1ST/2ND SELECTOR FORK- ROD CHANGE TYPE (NOT REMOTE) - TSP100390

TSP100390- SELECTOR FORK 1ST/2ND GEAR SELECTOR FORK ROD CHANGE

The shift fork in all gearboxes are designed to take a lot of abuse. They have to cradle a gear spinning at high RPM while forcing it into the next position. As the gears have to made of very hard steel, the shift fork must be soft enough not to damage the gear and yet take the abuse.

$159.09
($109.96 USD ) In stock

MINI 3RD/4TH SELECTOR FORK- REMOTE TYPE (NOT ROD CHANGE) - 22A610

22A610- MINI 3RD/4TH SELECTOR FORK- REMOTE TYPE (NOT ROD CHANGE)

Fitted all manual minis up until the introduction of Rod change gearboxes. This is the 3rd/4th fork - see 22A611 for 3 synchro 1st/2nd fork and 22G889 for 4 synchro 1st/2nd fork on Pre Rod types.

$127.23
($87.94 USD ) In stock

MINI & MOKE 3RD/4TH SELECTOR FORK- ROD CHANGE TYPE (NOT REMOTE) - TSP100400

TSP100400- SELECTOR FORK 3RD/4TH GEAR SELECTOR FORK ROD CHANGE

This is the only selector fork available for the rod change 3rd and 4th gear change. Secured in place by a roll pin (available as 22G2595) it replaces the earlier type which was held in place by a screw.

$127.23
($87.94 USD ) In stock

MINI & MOKE SELECTOR FORK ROLL PIN - ROD CHANGE - 22G2595

22G2595- MINI & MOKE SELECTOR FORK ROLL PIN - ROD CHANGE

Special shaped roll pin for the rod change selector forks

$3.59
($2.48 USD ) In stock

Mini rodchange (75 on) gearchange detent spring - 22G2083

22G2083- Mini rodchange detent spring

This is the spring that goes under your right hand side plate on the diff housing. this holds a spring tension on your gearchange. If this is weak it will/can jump out of gear.

$4.09
($2.83 USD ) In stock

Mini straight cut reverse gear 'rod change only' (16 & 18 tooth gear) - C-STR303

C-STR303- Mini straight cut reverse gear 'rod change only' (16 & 18 tooth gear)

Mini straight cut reverse gear 'rod change only' (16 & 18 tooth gear).

$153.64
($106.19 USD ) In stock

MINI & MOKE CENTRE OIL PICKUP - C-AHT54

C-AHT54 CENTRE OIL PICKUP

Mini Race Centre Oil pickup to suit all MINIs. This will stop any oil surge . . . . no matter how fast you take that corner next time!

$72.68 $59.95
($41.44 USD ) In stock

Mini Sump plug, long Magnetic type - DP1

DP1- MINI SUMP PLUG, LONG MAGNETIC TYPE

Magnetic drain plug, plus added length to help gather all those metal bits between oil changes. For all Mini's.

$30.00
($20.74 USD ) In stock

Mini sump plug repair bolt- tapered - DP2

DP2 - SUMP PLUG WITH TAPER FOR GEARBOX REPAIR

If you have stripped or ruined the sump plug thread in tyour gearbox, you have 2 easy alternatives. You can have a helicoil fitted or use this self cutting taper thread plug which must only be tightened enough without use of a washer to hold in the oil safely. Fitting instructions are included

$36.32
($25.10 USD ) In stock

Mini sumplug with magnet, fit all mini's - DAM7335

DAM7335- SUMPLUG MAGNETIC STANDARD DRAINPLUG

Original Sump Drain Plug, with magnetic pick up. The washer for this is AED172

$27.23 $18.14
($12.54 USD ) In stock

MINI & MOKE GEARBOX 4 SYNC REBUILD KIT (PRE A PLUS)-14MM MAINS - Rodchange_g/box_kit

RCGBBK01- Mini rodchange gearbox bearing overhaul kit

This is most things you will need to overhaul your rod change gearbox.- The only extra parts you may need (you will need to check your old ones) are the 'gear' bearings and synchro rings

$559.09 $522.73
($361.29 USD ) In stock

MINI & MOKE PINION "C" SHIM .002" - GUG705645GM

GUG705645GM- PINION "C" SHIM .002"

The shims go against the mainshaft double roller bearing securing cap in your gearbox to give it pre load. See workshop manual for advice but you are aiming for only 1 thou pre load.

$4.50 $3.59
($2.48 USD ) In stock

MINI & MOKE PINION "C" SHIM .004" - GUG705646GM

GUG705646GM- PINION "C" SHIM .004"

The shims go against the mainshaft double roller bearing securing cap in your gearbox to give it pre load. See workshop manual for advice but you are aiming for only 1 thou pre load.

$4.50
($3.11 USD ) In stock

MINI & MOKE ENGINE TO GEARBOX NUT AND BOLT KIT - MSSK060

MSSK060- MINI & MOKE ENGINE TO GEARBOX NUT AND BOLT KIT

Complete nut, bolt and washer set for engine to gearbox only.

$18.14
($12.54 USD ) In stock

SPEEDO DRIVE PINION 18 TEETH-SPI 3.2 final drive - TXD10006

TXD10006- SPEEDO DRIVE PINION 18 TEETH-SPI 3.2 final drive

Grey colour although some were red 18 tooth (18.8mm diameter) to go with the 7 tooth Red colour coded drive spindle TXF10004 which is 23mm in diameter- as opposed to DAM6028 @21.37mm wide (21.1 WORN) which is also 7 teeth-----Beware also of red colour plastic pinions DAM6365 from Metro boxes which were red (21mm diameter) SO NOTE-TXF10004 and TXD10006 were a special pairing.

Used in 3.2 diff ratio SPI gearboxes which were different to metro equivalents which had 13" wheels.

$72.68
($50.24 USD ) In stock