Minisport

Front panels

This section is from the front seam moulding to the very front of the car.

Pricing:
Sort by:

MINI SEAM MOULDING FRONT IN STAINLESS STEEL (PAIR) - 8B12400

8B12400 –MINI SEAM MOULDING FRONT IN STAINLESS STEEL (PAIR)

Body Seam Covers (Front) The seams of the Mini are designed to be covered. Both original and aftermarket strips are available and aftermarket Chromed Stainless steel version are also in stock for the very special Mini.

$90.86
($67.89 USD ) In stock

SEAM COVER CLIPS IN STAINLESS STEEL - BMP128MS

BMP128MS- SEAM MOULDING CLIP STAINLESS STEEL, ANTI RUST

These are the clips that hold on the vertical seam mouldings on all minis. The original metal type are prone to rust so Mini spares producedd these stainless steel versions (28 required for a full car, 7 clips per corner)

$1.77
($1.32 USD ) In stock

MINI FLAT WINDSCREEN SURROUND LOWER PANEL REPAIR - HMP441001

HMP441001- MINI (FLAT) WINDSCREEN SURROUND LOWER PANEL REPAIR

Genuine panel that has the holes for wipers and jets with only a few inches of pillar which is basically the area that rots. Also referred to as the windscreen scuttle lower panel. Fitting the genuine type ensures you should get a better windscreen and seal fit as they are from original pressings.

*Please note that these panels are not designed for our indented scuttle panels as fitted on Australian cars from april 1968 until 1978 however you could cut out parts that you need as a rust repair panel* 

$268.18
($200.37 USD ) In stock

Mini (all models) windscreen scuttle corner panel R/H - MS6R

MS6R- WINDSCREEN CORNER PANEL R/H

A non genuine panel made for repairing the corner of the windscreen panel which is prone to rust from water splashing up from underneath the front wheel arch.

$31.77
($23.74 USD ) In stock

Mini (all models) windscreen scuttle corner panel L/H side - MS6L

MS6L- WINDSCREEN CORNER PANEL L/H

A non genuine panel made for repairing the corner of the windscreen panel which is prone to rust from water splashing up from underneath the front wheel arch.

$31.77
($23.74 USD ) In stock

MINI WINDSCREEN CORNER SUPPORT PANEL R/H - MS6XR

MS6XR- MINI WINDSCREEN CORNER SUPPORT PANEL R/H

THIS PANEL PROTECTS THE UNDERSIDE OF THE WINDSCREEN VALANCE UNDER THE FRONT WING SECTION RIGHT HAND. Also fitted on the inner wing panel 14A8346 & 14A8347.

$31.77
($23.74 USD ) In stock

MINI WINDSCREEN CORNER SUPPORT PANEL L/H - MS6XL

MS6XL- MINI WINDSCREEN CORNER SUPPORT PANEL L/H

THIS PANEL PROTECTS THE UNDERSIDE OF THE WINDSCREEN VALANCE UNDER THE FRONT WING SECTION LEFT HAND. Also fitted on the inner wing panel 14A8346 & 14A8347.

$31.77
($23.74 USD ) In stock

MINI ENGINE STABILISER BRACKET LOWER ON BULKHEAD - 14A6730

This is the engine stabiliser bar original lower bracket that is welded on the engine bay bulkhead. This part often breaks away when the engine has been rocking around through poor maintenance of engine mounts and bushes. The upper bracket to this sits under the master cylinders.

$27.23
($20.34 USD ) In stock

Mini bulkhead panel to fit turbo - TURBO

TURBO- Mini bulkhead panel to fit turbo

This panel is an adaption panel that allows a turbo to fit at the back of the engine a lot easier. It would pay to check with your local authorites on the 'engineering' aspects of doing this. 

$117.27
($87.62 USD ) In stock