Minisport

Centre & floor panels

This section is from the front seam moulding to rear seam moulding where the rear meets the side of the car.

Pricing:
Sort by:

MINI FLOOR TO SILL REINFORCMENT BRACKET - 14A9550

14A9550- MINI FLOOR TO SILL REINFORCMENT BRACKET

Small reinforcement bracket panel between the inner and outer sill at the front, these are the same both sides. The 24A41 slinger sits underneath this bracket under the sill panel.

$36.32
($27.23 USD ) In stock

MINI FLOOR TO SILL REINFORCEMENT SLINGER BRACKET RH - 14A9552

14A9552- MINI FLOOR TO SILL REINFORCEMENT SLINGER BRACKET RH

Small reinforcement bracket panel between the inner and outer sill on the RH side rear. The 24A42 slinger sits underneath this bracket under the sill panel.

$18.14
($13.60 USD ) In stock

MINI FLOOR TO SILL REINFORCEMENT SLINGER BRACKET L/H - 14A9553

14A9553- MINI FLOOR TO SILL REINFORCEMENT SLINGER BRACKET L/H

Small reinforcement bracket panel between the inner and outer sill on the LH side rear. The 24A42 slinger sits underneath this bracket under the sill panel.

$18.14
($13.60 USD ) In stock

MINI FLOOR SLINGING BRACKET FRONT - 24A41

24A41- MINI FLOOR SLINGING BRACKET FRONT

Every mini saloon has these, 2 of 24A41 on either side front and 24A42/24A43 sided on the rear --only purpose was for building/moving/ storing and preparation of cars at the factory to sit them on. Also acted as a stiffener between the inner and outer sills which is why the factory fitted them to stop damage.

$20.86
($15.64 USD ) In stock

MINI REAR TRAILING ARM SHROUD- R/H - 14A6615

This small sheet metal panel mounts below the horizontal seam, covering the pivot pin of the rear R/H trailing arm. Unavailable for many years, they are now being reproduced. This shroud uses 14A7091 rubber plug not supplied

$18.14
($13.60 USD ) In stock

MINI REAR TRAILING ARM SHROUD- L/H - 14A6616

This small sheet metal panel mounts below the horizontal seam, covering the pivot pin of the rear L/H trailing arm. Unavailable for many years, they are now being reproduced. This shroud uses 14A7091 rubber plug not supplied

$18.14
($13.60 USD )
OUT OF STOCK (22/10/2021) CALL TO ORDER

MINI DOOR POST BOXING PLATE R/H - MBS001R

MBS001R- MINI DOOR POST BOXING PLATE R/H

A post inner closing panel/siffener plate R/H external hinge cars.

$45.41
($34.05 USD ) In stock

MINI DOOR POST BOXING PLATE L/H - MBS001L

MBS001L- MINI DOOR POST BOXING PLATE L/H

A post inner closing panel/siffener plate L/H external hinge cars.

$45.41
($34.05 USD ) In stock

MINI TOE BOARD PANEL- ALL MODELS - AHA36007

The first panel up towards the dash after the floor pans, at an angle and where steering rack bolts to floor without any brackets or fittings, see also same panel with steering rack fitting AHA36006 for 1976 on rubber mounted subframe or ALA6602 for pre 1976. This is the bare panel only i.e. no steering rack mounts etc.

 

$227.27
($170.42 USD ) In stock

MINI R/H RIGHT HAND FRONT FLOOR RUST REPAIR PANEL- EARLY TYPE - MS25R

This is the early R/H side floor rust repair panel; before they went to the 'hydrolastic' type that had the channel running down the middle of the well. This foot well is the rounded type (as was the original type).

$80.00
($59.99 USD ) In stock

MINI L/H RIGHT HAND FRONT FLOOR RUST REPAIR PANEL- EARLY TYPE - MS25L

This is the early L/H side floor rust repair panel; before they went to the 'hydrolastic' type that had the channel running down the middle of the well. This foot well is the rounded type (as was the original type).

$80.00
($59.99 USD ) In stock

Right hand front floor pans (rust sections) to suit Australian cars - MS25R_AUST

MS25R_AUST- Right hand front floor pan (rust section) to suit Australian cars

Front Right hand floor pan to suit Australian made cars (from 1965 to 1978) with wind up windows. These are exclusive with the hydro/fuel line protector chanel running through the center of the foot well. Has all captive nuts (for lower plate retention) **Extra shipping will be required**

$136.32 $122.73
($92.03 USD ) In stock

Left hand front floor pan (rust section) to suit Australian cars - MS25L_AUST

MS25L_AUST- Left hand front floor pan (rust section) to suit Australian cars

Front Left hand floor pan to suit Australian made cars (from 1965 to 1978) with wind up windows. These are exclusive with the hydro/fuel line protector chanel running through the center of the foot well. has all captive nuts (for lower plate retention) **Extra shipping will be required**

$136.32 $122.73
($92.03 USD ) In stock

MINI ROVER FLOOR PAN L/H FRONT (1991 ON) - MSL25L

MSL25L- MINI ROVER FLOOR PAN L/H FRONT (1991 ON)

This floor was made stronger with smaller heel pad area to prevent vibration and rust and will fit any Rod change gear shift mini but was introduced on the first injection cars in 1991 to allow pipes to be recessed.

$72.68
($54.50 USD ) In stock

MINI ROVER FLOOR PAN R/H FRONT (1991 ON) - MSL25R

MSL25R- MINI ROVER FLOOR PAN R/H FRONT (1991 ON)

This floor was made stronger with smaller heel pad area to prevent vibration and rust and will fit any Rod change gear shift mini but was introduced on the first injection cars in 1991 to allow pipes to be recessed.

$72.68
($54.50 USD )
OUT OF STOCK (18/03/2021) CALL TO ORDER