Minisport

Body Seals and rubber

 

Pricing:
Sort by:

Mini bonnet drain rubber, rear, fits on back lip - JRC7008

JRC7008- BONNET REAR DRAIN SEAL (GOES ON BACK LIP)

This seal actually fits on the rear bonnet lip and was always included in the ignition electrics protection kits. Found on all years of cars but fitted as standard in the 80s for a while.

$36.32
($28.32 USD ) In stock

MINI LEYLAND/CLUBMAN LOWER GRILLE SLOT BUFFER- 3D PRINTED - CZH614

CZH614- MINI LEYLAND/CLUBMAN LOWER GRILLE SLOT BUFFER- 3D PRINTED

This is the little  buffer that stops the grille from rattling against the body of the car. This has been 3D printed & will do the same job as the original one. Sold single- 3 required per car

$10.86
($8.47 USD ) In stock

Mini front subframe tower stud grommet (locktab is not included) - GROMMET06

GROMMET06- Dry suspension lock tab grommet.

This is the rubber grommet (32mm) that sits in the top of the subframe tower locktab- it will save you dropping your expensive sockets down the hole :) 

 

$5.41
($4.22 USD ) In stock

Mini Battery box rubber grommet (x3 req) made for replacement battery boxes - GROMMET07

GROMMET07- Mini Battery box rubber grommet (x3 req) made for the replacement battery box.

Mini Battery box rubber grommet (25mm) made for the replacement battery box. Suits the MS31- 3x grommets required for 1 battery box.

$3.59
($2.80 USD ) In stock

REAR UPRIGHT CHANNEL- ESTATE/TRAVELLER - 14A7630

14A7630- REAR UPRIGHT CHANNEL- ESTATE/TRAVELLER

Vertical fitting double row channel for sliding windows on the rear of mini traveller and estate rear windows (NOT AUSTRALIAN VANS)

$27.23
($21.23 USD ) In stock

FRONT UPRIGHT CHANNEL- ESTATE/TRAVELLER - 14A7631

14A7631- FRONT UPRIGHT CHANNEL- ESTATE/TRAVELLER

Vertical fitting double row channel for sliding windows on the front of mini traveller and estate rear windows (NOT AUSTRALIAN VANS)

$27.23
($21.23 USD ) In stock

VAN TOP CHANNEL (ESTATE/SLIDE) REAR WINDOW- 1080mm - 14A7632

14A7632- VAN TOP CHANNEL (ESTATE/SLIDE) REAR WINDOW- 1080mm 

Upper double row channel for the rear sliding windows on clubman estates

$54.50
($42.50 USD ) In stock

VAN LOWER CHANNEL (ESTATE/SLIDE) REAR WINDOW- 1220mm - 14A7633

14A7633- VAN LOWER CHANNEL (ESTATE/SLIDE) REAR WINDOW- 1220mm 

lower double row channel for the rear sliding windows on clubman estates- 1220mm

$54.50
($42.50 USD ) In stock

Mini jacking point grommet - 238.015

238.015- Mini jacking point hole grommet

If you have the jacking point hole in your mini (almost all of them do) then this grommet can be installed to ensure nothing decides to live in the underside of your car :)

$10.00
($7.80 USD ) In stock

MINI 850/COOPER WINDOW CHANNEL R/H FOR METAL CATCHES MK1 - 14A6769

14A6769- MINI 850/COOPER WINDOW CHANNEL R/H FOR METAL CATCHES MK1

Early Mini runner for metal type window catches pre May1963 with sliding windows on the front doors, these are the runners that hold the channel and have holes to lock the window catches. Now made in stainless steel by Minispares to ease rust problems. Also see 14A6770 for L/H.

Best to fit a pair so they look he same-Plastic catches were supposedly fitted from chassis number 15069 early may 1963 and the runners changed to 24A1303

$81.77
($63.77 USD ) In stock

MINI 850/COOPER WINDOW CHANNEL L/H FOR METAL CATCHES MK1 - 14A6770

14A6770- MINI 850/COOPER WINDOW CHANNEL L/H FOR METAL CATCHES MK1

Early Mini runner for metal type window catches pre May1963 with sliding windows on the front doors, these are the runners that hold the channel and have holes to lock the window catches. Now made in stainless steel by Minispares to ease rust problems. Also see 14A6769 for R/H.

Best to fit a pair so they look he same-Plastic catches were supposedly fitted from chassis number 15069 early may 1963 and the runners changed to 24A1304

$81.77
($63.77 USD ) In stock

MINI ROVER PLUG BOOT FLOOR GROMMET (92 ON) FOR FUEL LINES & NEW BOOT FLOORS - WYA10001

WYA10001- PLUG BOOT FLOOR GROMMET 92 ON FOR FUEL LINES

Fitted to injection cars to protect the injection pipes. This is also required if fitting a new boot floor into a mini (as they use this grommet)

 

$27.23
($21.23 USD )
OUT OF STOCK (09/03/2021) CALL TO ORDER

MINI ROVER CHECK ARM RUBBER GROMMET- R/H - CZH4052

CZH4052- MINI ROVER CHECK ARM RUBBER GROMMET- R/H

Moulded shape type left hand door stay grommet fitted until 1985 when it was replaced by a flat sponge type seal CGE10038/9

$11.77
($9.18 USD ) In stock

MINI ROVER CHECK ARM RUBBER GROMMET- L/H - CZH4053

CZH4053- MINI ROVER CHECK ARM RUBBER GROMMET- L/H

Moulded shape type left hand door stay grommet fitted until 1985 when it was replaced by a flat sponge type seal CGE10038/9

$11.77
($9.18 USD ) In stock

MOKE REAR BONNET HINGE SUPPORT RUBBERS - HYA4000

These are the rear bonnet hinge support rubbers for the moke hinges.

$9.05
($7.05 USD )
OUT OF STOCK (14/01/2021) CALL TO ORDER