Minisport

SU PARTS, CARBURETORS AND FUEL SYSTEMS

Pricing:
Sort by:

Mini single carby (1-1/4 to 1-1/2") return spring - 1E5537

1E5537- Mini carby return spring (1-1/4 or 1-1/2)

This is the spring that pulls the throttle bracket back to idle, fits down to a bracket on the exhaust on 1-1/4" or to the bracket on 1-1/2"

$4.50
($3.04 USD ) In stock

Mini Reconditioned 1-1/4" carby **EXCHANGE** - RECO_1-1/4" +$75

RECO_QTR - Mini 1.25" (1-1/4") fully rebuilt carby **EXCHANGE**

This is a fully overhauled 1.25" carby, it has had a full gasket set, new oversized spindleshaft installed, new butterfly, new main jet, new needle and seat.

EXCHANGE only, a fully refundable deposit of $75 will apply on top of the cost of this item

$318.18
($215.07 USD ) In stock

Mini Reconditioned 1-1/2" carby **EXCHANGE** - RECO_1-1/2" + $150

RECO_HALF - Mini 1.5" (1-1/2") fully rebuilt carby **EXCHANGE**

This is a fully overhauled 1.5" carby, it has had a full gasket set, new oversized spindleshaft installed, new butterfly, new main jet, new needle and seat.

EXCHANGE only, a fully refundable deposit of $150 will apply on top of the cost of this item

$318.18
($215.07 USD ) In stock

Mini HIF44 carby(as used on 1275 metro's in the UK) - FZX3006

FZX3006- CARBURETTOR HIF44 1982 METRO 0N INCLUDING UNLEADED

THIS CARB IS A GREAT TUNING AID ON TUNED ENGINES, ESPECIALLY 1380cc, use with the supercharger kit! Fuel bowl is located underneath the carby- 1-3/4" mounting stud patern! 

$813.64
($549.97 USD )

OUT OF STOCK

TWIN SU FUEL BOWL CONNECTING PIPE - 12G292

12G292- PIPE TWIN SU CARB TO CARB

Original shape of petrol feed pipe for twin HS" carbs as fitted to all the Coopers.

$30.00
($20.28 USD ) In stock

Mini twin SU accelerator return spring - AEC2075

AEC2750

Mini twin carby return spring, suits either twin 1-1/4" or 1-1/2"

$4.50
($3.04 USD ) In stock

MINI & MOKE THROTTLE BRACKET ON MANIFOLD FOR TWIN CARBS - AEG349

AEG349- MINI & MOKE THROTTLE BRACKET ON MANIFOLD FOR TWIN CARBS

This is the throttle bracket that bolts onto the manifold on twin carby setups.

$18.14
($12.26 USD ) In stock

1/4" UNC BOLT (3/4" LONG) - GHF160

GHF160- 1/4" UNC BOLT (3/4" LONG)

This is the bolt used to hold the throttle bracket (AEG349) onto the manifold and for holding plate on speedo drive housing on gearbox.

$1.41
($0.95 USD ) In stock

Mini cooper s twin carby accelerator cross shaft - 12A310

12A310- TWIN CARB BUTTERFLY LINKAGE

The rod with the plate is called the butterfly rod and was fitted to all Cooper twin carb HS2 set ups.

$22.68 $16.32
($11.03 USD ) In stock

Mini twin carby linkage kit, suits either 1.25 or 1.5 carbys - MSSK009

MSSK009- TWIN CARB LINKAGE KIT, SUITS EITHER 1.25” OR 1.5”

This fitting kit suits all later day 1.25" and 1.5" twin carb set ups where the balance rods between the carbs required are equal length(2.25"),some early carbs had the balance bar with a triangular plate that were a shorter length. The kit has the original type abutment bracket that fits to the inlet manifold to guide the accelerator cable.

$63.59
($42.98 USD ) In stock

Mini fuel bowl rubber buffer (cut on L/H side) 1336 - AUD2178

AUD2178- Mini fuel bowl buffer (L/H cut) -1336

This is the buffer that goes on some carbys (mainly twins) between the fuel bowl and the carby body, there is a L/H and a R/H this rubber has the cut at about '11 o'clock position'

$12.00
($8.11 USD ) In stock

Mini fuel bowl rubber buffer (cut on R/H side) 1316 - AUD2179

AUD2179- Mini fuel bowl buffer (r/h cut) -1316

This is the buffer that goes on some carbys (mainly twins) between the fuel bowl and the carby body, there is a L/H and a R/H this rubber has the cut at about 1 o'clock position

$12.00
($8.11 USD ) In stock

Mini fuel bowl bolt grommet (when buffer fitted) - AUC1318

AUC1318- Fuel bowl bolt buffer

This is the grommet that goes on the bolt to the fuel bowl when the buffer (either) is fitted

$5.45
($3.69 USD ) In stock

MINI & MOKE BOOSTER FITTING FOR MANIFOLD- AFTERMARKET TYPE - 12H1405MS

12H1405MS- MINI & MOKE BOOSTER FITTING FOR MANIFOLD- AFTERMARKET TYPE

Aftermarket union for fitting all mini inlet manifolds where a take off is required for your brake servo or emission valve on Cooper S cars.

$18.14
($12.26 USD ) In stock

MINI & MOKE BOOSTER FITTING FOR MANIFOLD- ORIGINAL TYPE - 12H1405

12H1405- Servo fitting for the booster outlet on twin carby mainfold

This is a fitting that screws into the twin carby manifold, it allows you to feed in your servo. this will suit the C-AHT770 single manifold too.

$22.68
($15.33 USD ) In stock