Minisport

Clutch

The mini clutch is one of the most unique clutch setups on ANY cars, rarely do everyday automotive parts suppliers understand or stock parts for your mini clutch. This clutch section is one of the most comprehensive on the net!...We not only stock the parts but we know trade tricks to get you the best clutch pedal possible (as we fit them as well).

Pricing:
Sort by:

MINI & MOKE SLAVE CYLINDER RETURN SPRING ANCHOR TAB - 2A3600

Anchor tab for return spring that fits behind bleed valve on Slave cylinders, for Pre Verto clutches. The clutch spring 1G5999 connects onto this.

$4.09
($2.80 USD ) In stock

MINI & MOKE CLUTCH RETURN SPRING ANCHOR FOR GENUINE CLUTCH ARM - 2A3601

This plate is on the end of the PRE A plus original long type clutch arm 22A2204 to hold the return spring 1G5999. The clevis pin to hold this on the arm is CLZ518. If you have the later Mini Spares arm with 22A2204 stamped on side with a square end you require the 2A3601MS. This plate is 20mm wide spring end and 25mm wide clevis pin fitting end.

$10.00
($6.83 USD ) In stock

MINI & MOKE CLUTCH RETURN SPRING ANCHOR FOR 'NEW' LEVER ARMS - 2A3601MS

This plate is on the end of the PRE A plus long type clutch arm 22A2204MS to hold the return spring 1G5999. The clevis pin to hold this on the arm is CLZ518- this is the square type but for earlier tapered type Rover arm see 2A3601. This plate is 20mm width both ends.

$10.00
($6.83 USD ) In stock

MINI & MOKE CLUTCH RETURN SPRING - 1G5999

Mini & Moke clutch arm return spring for the return of the slave cylinder push rod. One end connects to the slave cylinder tab 2A3600 & the other end connects to the clutch arm anchor 2A3601. 

$7.23
($4.94 USD ) In stock

MINI & MOKE CLUTCH PUSH ROD - 13H396

This is the push rod at the top of your clutch arm- it connects the clutch arm to the slave cylinder. This is held into the arm by a clevis pin CLZ518. Check the eye piece for wear as this is normally where the problems with the push rod arm.

$19.95
($13.64 USD ) In stock

MINI & MOKE CLUTCH PUSH ROD- ADJUSTABLE TYPE - 13H396ADJUSTABLE

This is an adjustable push rod for your clutch arm setup; for when you just need a bit more length [don't we all want that].

$36.32
($24.82 USD ) In stock

MINI & MOKE CLEVIS PIN CLUTCH ARM- TOP - CLZ518

Clevis pin at the top of the clutch arm. The pin is 5/16" size

$4.00
($2.73 USD ) In stock

MINI & MOKE CLUTCH LEVER ARM- HEAVY DUTY (PRE VERTO) - 22A2204MS

This is the Mini & moke clutch arm that goes from the plunger to the pushrod. Ensure you adjust the clutch properly otherwise the hydraulics are powerful enough to bend the ball end of the clutch arm, whether it be a genuine or pattern part.

$59.05
($40.36 USD ) In stock

MINI & MOKE CLEVIS PIN CLUTCH ARM- BOTTOM - CLZ628

The large clevis pin that goes through the clutch lever arm at the bottom of all minis & Mokes.

$6.32
($4.32 USD ) In stock

MINI & MOKE CLUTCH THRUST BEARING PLUNGER- PRE VERTO - 22A180MS

This a mini & Moke carrier that holds the clutch release bearing (thrust) and on the other end has a hole for the clutch lever arm. This is the pre verto type. This is the non genuine type but works perfectly fine.

$20.00
($13.67 USD ) In stock

MINI & MOKE CLUTCH THRUST BEARING PLUNGER- EN24 STEEL - 22A180

This is the carrier that holds the clutch release bearing and on the other end has a hole for the clutch lever arm. Upgraded pre verto clutch lever arm plunger. 

$36.32
($24.82 USD ) In stock

MINI & MOKE CLUTCH THROW OUT PLUNGER FLANGED NUT - 22A427

The large special shaped 'flanged' nut on the adjusting end of the clutch plunger which holds the release bearing. The flat locking nut for this is NT610041

$13.59
($9.29 USD )
OUT OF STOCK (01/03/2022) CALL TO ORDER 

MINI & MOKE CLUTCH THROW OUT PLUNGER LOCKNUT - NT610041

The locking nut for the clutch throw out plunger. The special flanged nut is 22A427. 

$6.32
($4.32 USD ) In stock

MINI & MOKE COMPETITION CLUTCH ARM AND PLUNGER KIT- RACE - C-22A2204

Race quality tuftrided clutch arm kit made in EN24T for any heavy duty diaphragm- special design plunger with arm to suit, hardened clevis pin and R-clip included.

$222.73
($152.23 USD )

OUT OF STOCK (20/06/2022) CALL TO ORDER

MINI & MOKE CLUTCH THRUST/RELEASE BEARING (PRE VERTO) - 7W5-8/GRB201

7W5-8/GRB201- MINI & MOKE CLUTCH THRUST/RELEASE BEARING (PRE VERTO)

If you get a ‘growling’ noise when you put your foot on the clutch pedal chances are that the Thrust bearing is knackered, it is important to replace it as soon as you can because this will eventually lead to complete clutch pedal loss and the car will be immobile. (A Very low clutch pedal can also indicate a problem as well)

$20.00
($13.67 USD ) In stock