Minisport

MINI & MOKE DRUM BRAKE ADJUSTING SPANNER (AND 1/4" BLEED NIPPLE) - BLM810

One end is 5/16" open end for the brake adjuster, the other is 1/4" closed end to fit the original bleed screws. The wrench has just the right offset and length to make the job easy!

MINI SINGLE LEADING FRONT WHEEL CYLINDER- 850 & COOPER - GWC101

Single leading brakes were fitted to the early 850 minis, these are brand new and there is no exchange required. (SOLD SINGLE).

MINI & MOKE FRONT TWIN LEADING 15/16" WHEEL CYLINDER- R/H - 4410/GWC126

This is a 15/16 wheel cylinder. We recommend replacing all front wheel cylinders when one is leaking (to avoid any brake pulling). This is the R/H side (two required per side) SOLD SINGLE.

MINI & MOKE FRONT TWIN LEADING 15/16" WHEEL CYLINDER- L/H - 4409/GWC127

This is a 15/16 wheel cylinder. We recommend replacing all front wheel cylinders when one is leaking (to avoid any brake pulling). This is the L/H side (two required per side) SOLD SINGLE.

MINI & MOKE FRONT TWIN LEADING WHEEL CYLINDER 1 INCH- R/H - P6908

The 1.000" front wheel cylinder is an upgrade on the 15/16 wheel cylinders We recommend replacing all front wheel cylinders when one is leaking (to avoid any brake pulling). This is the R/H side (two required per side) SOLD SINGLE

MINI & MOKE FRONT TWIN LEADING WHEEL CYLINDER 1 INCH- L/H - P6909

The 1.000" front wheel cylinder is an upgrade on the 15/16 wheel cylinders We recommend replacing all front wheel cylinders when one is leaking (to avoid any brake pulling). This is the L/H side (two required per side) SOLD SINGLE.

MINI & MOKE BLEED NIPPLE 3/8 UNF THREAD - 3H2428

3H2428- BLEED NIPPLE 3/8 UNF THREAD

Bleed nipple for front wheel cylinders on twin leading shoe type set ups,this is where you have 2 cylinders per hub as single laeding type which had one cylinder only per hub, also will fit front calipers on disc assemblies

Mini front wheel cylinder gasket (sold single) - 37H3833

37H3833 - Mini front wheel cylinder gasket

This gasket is fitted between the backing plate and the wheel cylinder on any model that had 2 front wheel cylinders per side. These are not necessay, but will prevent dirt/dust and water getting in.

MINI & MOKE BRAKE SHOE RETAINING SPRING. - 27H3753

Mini front drum retaining clip, this clip holds the brake linings to the piston of the wheel cylinder used on all front drum brakes (except 850)

Mini front drum brake shoe spring kit (4 in a kit) - GBK1733

GBK1733- BRAKE SHOE SPRINGS FRONT KIT (4)SPRINGS

If you have original drum brakes on the front of your mini this is the kit of 4 tension springs you should change on the brake shoes. These springs when old can become weak and loose tension. For the price why wouldn’t you!

The small conical spring to hold the shoe to the back-plate is 27H3753

Mini twin leading front backing plate (L/H) - 37H2014

37H2014- Twin leading front backing plate (L/H)

Genuine L/H original AP backplate- If the brake adjusters on your front twin-leading brakes have seized up or are worn out, there is no real repair short of replacing this backplate!

Mini twin leading front backing plate (R/H) - 37H2013

37H2013- Twin leading front backing plate (R/H)

Genuine R/H original AP backplate- If the brake adjusters on your front twin-leading brakes have seized up or are worn out, there is no real repair short of replacing this backplate!

Mini front drum brake linings (set of 4) NEW - GBS102MS

GBS102MS- BRAKE SHOES SET FRONT (685)

Brake shoes for Mini twin-leading front drum brakes. A good mechanic will replace the pull-off springs (GBK1733) when installing new shoes. The return springs rust and fatigue over time and may have been damaged by improper installation in the past.

MINI & MOKE BRAKE DRUM- NON STEPPED TYPE - GDB105

GDB105- MINI NON STEPPED BRAKE DRUM (SINGLE)

The front and rear brake drums on a standard Mini are the same..this one. Uses 1 1/4" shoes (GBS101) on the rear and single-leading front and 1 1/2" shoes (GBS102) on twin-leading front only.

MINI & MOKE BRAKE DRUM- STEPPED TYPE (1 INCH) - GDB106

This is a brake drum with the 1 inch spacer built on, this was used on the many models. These are also used when fitting wheels and needing the spacer to clear the suspension componets. 7" internal diameter.