Minisport

MINI & MOKE DRUM BRAKE ADJUSTING SPANNER (AND 1/4" BLEED NIPPLE) - BLM810

One end is 5/16" open end for the brake adjuster, the other is 1/4" closed end to fit the original bleed screws. The wrench has just the right offset and length to make the job easy!

MINI & MOKE BRAKE ADJUSTING KIT- REAR (& EARLY 850 FRONT) - 17H7620

This is the adjuster and two wedges that were fitted to the the rear of all minis & mokes that have rear drum brakes. These were also fitted onto the front of single piston 850 brakes (not twin leading setup).

MINI & MOKE REAR BRAKE WHEEL CYLINDER 3/4"- SOLD SINGLE - 4411/GWC1102MS

All later models have these 3/4" bore double piston cylinders for the rear brakes. INCLUDES BLEED NIPPLE AND CLIP. If you are unsure if this will fit your car- please measure the bore of your old wheel cylinder piston- or contact us.

MINI & MOKE REAR BRAKE WHEEL CYLINDER 3/4"- GENUINE AP - GWC1102-AP

Genuine AP [Made in UK] rear wheel cylinder with 3/4"(19mm) bore Lockheed double piston type as fitted to all cars from 1970 except "S". Includes bleed nipple, retaining clip and gasket. Bleed nipple now 7mm spanner size but same thread-original 513118A

MINI & MOKE REAR BRAKE WHEEL CYLINDER 5/8"- SOLD SINGLE - 4412/GWC1101MS

0.625-5/8" rear wheel cylinder used from 1959-1967 when using disc brakes on the front end (keeps the back end less active). Quantity one per rear wheel and 2 required for car set. Bleed nipple now 7mm spanner size but same thread-original 

MINI & MOKE REAR BRAKE WHEEL CYLINDER 5/8"- GENUINE AP - GWC1101-AP

Genuine AP [Made in England] rear wheel cylinder in 5/8" [0.625mm] bore-Fitted to all Cooper 'S' hydrolastic cars from Sept 1964 plus mini to 1967. Also used from 1959-1963 and intermittently on. Leyland used this smaller type cylinder with servo on disc set ups as standard.

MINI & MOKE REAR BRAKE WHEEL CYLINDER 11/16"- SOLD SINGLE - 4414/GWC1129

In Australia the Rear wheel cylinder with 0.6875" bore size first appeared in 1974 on single line MOKE. In the UK they used these on the UK SPEC 1275GT cars and then on some split diagonal until 1976- also fitted to Innocenti cars when they had a unique 4 way swith union. 

MINI & MOKE REAR WHEEL CYLINDER TO BACK PLATE GASKET - 37H4642

This paper gasket will fit all minis & mokes. It is fitted between the rear wheel cylinder and the backplate. Once supplied with most wheel cylinders but many suppliers have discontinued this practice.

MINI & MOKE BLEED NIPPLE REAR WHEEL CYLINDER 1/4"unf - 513118A

513118A- MINI & MOKE- BLEED NIPPLE REAR WHEEL CYLINDER 1/4"unf

Bleed nipple for all rear wheel cylinders plus GWC101 and is 1/4"unf thread. current wheel cylinders are using 7mm rather than 6.2mm(1/4") spanner size but same thread.

MINI & MOKE BLEED NIPPLE DUST COVER CAP - STC1913

This is the little dust cover cap that stops dirt and road grime getting into the brake bleeder valve. These fit bot the front 3H2428 front bleed nipples and the 513118A rear bleed nipples. Open advert for more images of these fitted on the nipple(s).

MINI & MOKE REAR WHEEL CYLINDER RETAINING CLIP - 17H7949/1

17H7949- Mini rear wheel cylinder retaining clip

This clip holds the rear wheel cylinder to the backing plates, they are the same on all models and do not differ, they where also fitted on the front of 850 single wheel cylinder brake setups. Easy to break!

MINI & MOKE REAR WHEEL CYLINDER CIRCLIP INSTALLING TOOL. - TOOL14

A handy little gadget for installing/fitting the circlip holding the rear wheel cylinder on. Fits mini & moke. Please make sure you have the clip the correct way around (as per the images in the detailed advert)

3/4" BORE REAR WHEEL CYLINDER REPAIR KIT FOR GWC1102 - GRK2014

Sometimes your old 3/4" bore wheel cylinders only need a service kit installed. These fit the 3/4" bore (GWC1102) rear wheel cylinders. When installing PLEASE make sure the bore of your wheel cylinders is not pitted with rust. One kit does one wheel cylinder (2 required per car) 

5/8" BORE REAR WHEEL CYLINDER REPAIR KIT FOR GWC1101 - GRK2076

Sometimes your old 5/8" bore wheel cylinders only need a service kit installed. These fit the 5/8" bore GWC1101 rear wheel cylinders. When installing PLEASE make sure the bore of your wheel cylinders is not pitted with rust. One kit does one wheel cylinder (2 required per car) 

MINI & MOKE BRAKE SHOE SET FOR REAR- MS - GBS101MS

GBS101MS- BRAKE SHOES SET REAR (686)

1 1/4" rear brake shoes, set=2 pairs.

Brake shoes for Mini single-leading front drum brakes (850) and all 10" Mini rears.