Minisport

Gaskets and seals

Pricing:
Sort by:

MINI & MOKE ROCKER COVER RUBBER GROMMET- SOLD SINGLE - AYH241

This is the grommet that goes under the rocker cover bolt & washer. Sold singly, 2 required per engine.

$4.50
($3.08 USD ) In stock

ROCKER COVER CORK GASKET (EXCEPT 11 STUD HEADS) - GUG705009VC

Cork rocker cover gasket, suitable for all A series engines except those with 11 stud heads (see part number GUG5038VC). A must have replacement item when adjusting rocker clearances.

$7.27
($4.97 USD ) In stock

MINI & MOKE ROCKER COVER GASKET COOPER S AND 11 STUD HEADS - GUG5038VC

This has the cut out for the 11 stud cylinder heads as used on the original Cooper S variants but will fit ALL other rocker covers (850-1100).

$7.27
($4.97 USD ) In stock

MINI/MOKE ROCKER COVER GASKET SILICONE 9 STUD HEAD - GUG705009EVO

Upgraded rocker cover gasket made in silicon, ideal for race cars etc where the rocker cover is removed on a regular basis. Mini Spares have one on their 1380cc engine with great results.

$22.68
($15.50 USD ) In stock

MINI/MOKE ROCKER COVER GASKET SILICONE 11 STUD HEAD - GUG5038EVO

Upgraded rocker cover gasket made in silicon, cut outs for 11 stud head and ideal when rocker cover is removed on a regular basis.

$22.68
($15.50 USD ) In stock

MINI & MOKE HEATER TAKE OFF GASKET- THIN PAPER TYPE GASKET - AYA179

This is the thin gasket that goes between the heater take off and the head on almost all mini, moke & A series heads.

$1.36
($0.93 USD ) In stock

MINI & MOKE HEATER TAKE OFF GASKET- THICK TYPE GASKET - 88G221

88G221- MINI & MOKE HEATER TAKE OFF GASKET- THICK TYPE GASKET

This is the gasket that goes between the heater take off and the head on almost all mini & moke heads. This is the thick type gasket.

$1.77
($1.21 USD ) In stock

MINI & MOKE TAPPET CHEST COVER FIBRE WASHER - 12A1174

Mini & Moke tappet chest cover fibre washer (2 required per bolt). Normally used with the thin type cork gasket (12A1139) setup. Sold single, 4 required per engine.

$0.91
($0.62 USD ) In stock

MINI & MOKE CORK TAPPET CHEST COVER GASKET- FLAT TYPE - 12A1139

This is the thin cork tappet chest gasket as fitted to the 'flat type' tappet chest covers. This type of thin cork gasket used two thin fibre washers (12A1174) per bolt. SOLD SINGLE- 2 REQUIRED PER ENGINE 

$3.64
($2.49 USD ) In stock

MINI & MOKE TAPPET CHEST COVER RUBBER GROMMET - 12A1176

This is the rubber grommet that goes into the cup washer (12A1177) and goes around the bolt to stop oil from getting out of the chest cover. SOLD SINGLE- 2 REQUIRED PER ENGINE 

$2.68
($1.83 USD ) In stock

MINI & MOKE TAPPET CHEST COVER CUP WASHER - 12A1177

The special washer under the tappet cover bolt, as fitted to later type covers (with recessed gasket area). SOLD SINGLE- 2 REQUIRED PER ENGINE 

$2.68
($1.83 USD ) In stock

MINI & MOKE RUBBER TAPPET CHEST COVER GASKET- RECESSED TYPE - 12A1175

This seal is fitted behind the exhaust/inlet manifold. This seal is made for the recessed type covers that had the thick cork gasket. The thick cork gasket is not available and is now replaced with this rubber gasket. SOLD SINGLE- 2 REQUIRED PER ENGINE

$3.64
($2.49 USD ) In stock

GASKET SEALANT- NON HARDENING- AVIATION GRADE - 3J

3J- GASKET SEALANT- NON HARDENING- AVIATION GRADE

This is the ultimate in gasket sealant, this is aviation grade non hardening sealant

$9.05
($6.18 USD ) In stock

MINI & MOKE OIL PRESSURE RELEASE VALVE COPPER WASHER - 6K431

The oil pressure relief valve consists of an aluminum plunger with a heavy spring behind it. Access is through the 15/16" domed cap nut beside the dizzy. Once this nut is removed to prevent oil leaks, it is always a good idea to replace the copper washer (6K431) under the domed nut.

$2.23
($1.52 USD ) In stock

MINI & MOKE WATER PUMP GASKET- GENUINE QUALITY - GUG705555GM

GUG705555- MINI & MOKE WATER PUMP GASKET- GENUINE QUALITY

Genuine water pump gasket, red one side and grey the other, grey side to the water pump.

$5.00
($3.42 USD ) In stock