Minisport

MINI & MOKE HEATER TAKE OFF GASKET- THIN PAPER TYPE GASKET - AYA179

AYG172- MINI & MOKE HEATER TAKE OFF GASKET- THIN PAPER TYPE GASKET

This is the gasket that goes between the heater take off and the head on almost all mini heads.

MINI & MOKE HEATER TAKE OFF GASKET- THICK TYPE GASKET - 88G221

88G221- MINI & MOKE HEATER TAKE OFF GASKET- THICK TYPE GASKET

This is the gasket that goes between the heater take off and the head on almost all mini & moke heads. This is the thick type gasket.

MINI & MOKE HEATER VALVE BLANKING PLATE FOR CYLINDER HEAD - 2A180

2A180- HEATER VALVE BLANKING PLATE FOR CYLINDER HEAD

Use this plate in place of the heater valve. For use any time the heater is removed!

MINI & MOKE HEATER VALVE BLANKING PLATE FOR CYLINDER HEAD- STAINLESS STEEL - SMB119

SMB119- MINI & MOKE HEATER VALVE BLANKING PLATE FOR CYLINDER HEAD- STAINLESS STEEL

Use this plate in place of the heater valve. For use any time the heater is removed! Stainless steel with bolts & gasket (as shown)

MINI & MOKE HEATER TAKE OFF PIPE- 1/2" HOSE- RIGHT ANGLE - 12G2534AUST

12G2534AUST- MINI & MOKE HEATER TAKE OFF PIPE- 1/2" HOSE- RIGHT ANGLE

This heater take off pipe fits on the cylinder head of your mini engine- Only availabe secondhand they all have signs of wear & corrosion BUT with a bit of silicon these are more than useable. 

MINI & MOKE HEATER TAKE OFF PIPE- 5/8" HOSE - 12G2534

12G2534- MINI & MOKE HEATER TAKE OFF PIPE- 5/8" HOSE (ROVER TYPE)

Once the old type alloy heater valve on the head was discontinued in 1990 for the plastic free floating inline type this take off union was fitted in its place on A series engine cars for use with the larger 5/8" hose. Uses 88G221 gasket.

HEATER TAP (ON HEAD TYPE) ANGLED ORIGINAL SHAPE - ADU9102MS

ADU9102MS- HEATER TAP (ON HEAD TYPE) ANGLED ORIGINAL SHAPE

The original RANCO tooling has been scrappped so beware of some imports available where the inners quickly explode loosing the metal cap and all your water when operated.This has M4 metric thread bolt included for the cable screw instead of the 11/31" unc thread original.

UNIVERSAL HEATER TAP- 1/2"(13MM) HOSE- PULL TO OPEN - C-ARA3002

C-ARA3002- UNIVERSAL HEATER TAP- 1/2"(13MM) HOSE- PULL TO OPEN

This is a fully serviceable universal heater tap. The hose diameter it suits is 1/2 inch or 13mm. This setup is cable operated and is supplied with a bracket & two clips to secure the cable to the bracket. As the cable pushes it will CLOSE the valve.

Mini heater tap stud (stainless steel) 1/4" UNF - 53K402S

53K402S- Stainless steel heater tap stud for the cylinder head.

Stainless steel heater tap stud for the cylinder head.

MINI LEYLAND/CLUBMAN HEATER TAP - HYL4363

HYL4363- MINI LEYLAND/CLUBMAN HEATER TAP

This heater tap was fitted to the heater of a mini clubman and sits down near the floor on the passengers side, if you heater in the clubman doesn’t work then chances are this is the problem.-

This heater tap is a replacement for the original but WILL change the 'hot/cold' location on your dash panel- this can be rectified by altering the heater tap (a how too is available upon request).

MINI OR MOKE BLANKING PLATE FOR BULKHEAD WHEN NO HEATER HOSES - ALA6593

ALA6593- MINI OR MOKE BLANKING PLATE FOR BULKHEAD WHEN NO HEATER HOSES

Blank plate on bulkhead with no holes for heater hoses. There are 3 types (ALA7530 with holes) or (ALA6592 with one hole) or (ALA6593 blank no holes).

MINI OR MOKE FIREWALL BLANKING PLATE WITH 2 HOLES - ALA7530

ALA7530- FIREWALL BLANKING PLATE WITH 2 HOLES

Plate on bulkhead with 2 holes for heater hose- There are 3 types (ALA7530 with holes) or (ALA6592 with one hole) or (ALA6593 blank no holes).

MINI & MOKE MASTER CYLINDER PLATE OR HEATER PLATE GASKET - NAM9197

NAM9197- MINI & MOKE MASTER CYLINDER PLATE OR HEATER PLATE GASKET (SOLD SINGLE)

The gasket that sits under the plate which the brake and clutch master cylinders sit on, single brake line type. Also used under the heater plate gasket.

MINI 'ROVER' HEATER VALVE TWIN POINT ONLY FITTED ON SIDE OF HEATER UNIT - JJB100260

JJB100260- MINI 'ROVER' HEATER VALVE TWIN POINT ONLY FITTED ON SIDE OF HEATER UNIT

Twin point Mini heater tap that fits to the heater assembly.

UNIVERSAL HEATER TAP- 1/2"(13MM) HOSE- PUSH TO OPEN - C-ARA3004

C-ARA3004- UNIVERSAL HEATER TAP- 1/2"(13MM) HOSE- PUSH TO OPEN

This is a fully serviceable universal heater tap. The hose diameter it suits is 1/2 inch or 13mm. This setup is cable operated and is supplied with a bracket & two clips to secure the cable to the bracket. As the cable pushes it will OPEN the valve.