Minisport

Inlet manifolds & fittings

Pricing:
Sort by:

MINI & MOKE WATER HEATED 1-1/2" & 1-3/4" INLET MANIFOLD- ALLOY - C-AHT770

C-AHT770 Mini water heated manifold,

A must for anyone who wants to fit extractors, this manifold will heat up the aluminium manifold to allow better fuel atomisation, (the standard manifold was mounted to the exhaust headers.

Will fit 1-1/2, 1-3/4, HIF38 & HIF44

$90.00
($61.41 USD ) In stock

MINI & MOKE TWIN 1-1/4" INLET MANIFOLD- ALLOY - C-AEG488

C-AEG488- MANIFOLD TWIN INLET HS2 ONLY

Cast alloy type, this intake manifold for twin SU’s (H2, HS2 or H4 -- NOT HS4) It has been carefully produced to minimize cross-port-flow interference caused by the balance tube and has generous radii in all the right places.

$177.27
($120.96 USD ) In stock

MINI & MOKE TWIN 1-1/2" INLET MANIFOLD- ALLOY - C-AEG489

C-AEG489- MINI & MOKE MANIFOLD TWIN INLET HS4/6 (1.5" OR 1.75")

Cast alloy type, Fits either twin HS4 or HS6.(requires modifacation to fit HS6.2 extra studs per carb)

$181.82
($124.06 USD ) In stock

MINI & MOKE 5/16" STUD- HS4 /HIF CARB - CHS2514

CHS2514- MINI & MOKE 5/16" STUD- HS4 /HIF CARB

Universal stud made for fitting the HS4/HIF carb to the manifold (except HS6 with alloy spacer on cast one piece manifold which requires CHS2515 (5.8mm longer)) and it also fits the cylinder head to take the thermostat housing. Note that HS2 carbs require larger CHS2613/4 studs, 5/16" unc with unf thread for nut.

$4.50
($3.07 USD ) In stock

MINI & MOKE 5/16" STUD- THERM HSG STUD/HS4 SU - CHS2515

CHS2515- STUD FOR THERMOSTAT HOUSING WITHOUT SANDWICH PLATE (5/16")

Probably the most changed stud on the mini? This is the length used on every A series engine until the introduction of the sandwich plate when longer ones were replied. 5/16"unc and unf at nut end,this bolt is about 4.5cm long about 3.5cm from the bottom of the UNC thread

$4.50
($3.07 USD ) In stock

MINI & MOKE 3/8" STUD- OIL FILTER/HS2 CARB ETC - CHS2613

CHS2613- STUD FOR SCREW ON OIL FILTER plus HS2 CARB (2 required)

1.6250" long stud for engine block to accept the TAM097 screw on filter head and for HS2 carbs--alternative to this is CHS2614 1.75" long and just over one thread longer.

$4.50
($3.07 USD ) In stock

MINI & MOKE SU ADAPTOR (1-1/2 TO 1-1/4") - C-AHT770ADAPT

C-AHT770ADAPT- MINI & MOKE SU ADAPTOR (1-1/2 TO 1-1/4")

This bracket has been designed around the C-AHT770 inlet manifold, it is an adaptor bracket that converts the 1-3/4" mounting flange back down to the 1-1/4" carby mounting flange. This allows the C-AHT770 to be used on any size carby.

$45.41
($30.98 USD ) In stock

MINI & MOKE INLET MANIFOLD LOCATING RING (12G295 HEADS) - 12G297

12G297- INLET MANIFOLD LOCATING RING

Locating rings originally made for 12G295 heads with twin carbs to lign up the inlet maniold to the inlet ports on the cylinder head it found its way on most twin carb factory produced cars. There is a recess in the inlet port on the head and usually the inlet manifold to take these spacers.

$2.68
($1.83 USD ) In stock

MINI & MOKE CARBY MANIFOLD BLANKING PLUG- HEX HEAD TYPE - 5-8UNF

5-8UNF- PLUG 5/8UNF X 5/8 SCREW INLET MANIFOLD & CYL HEAD BY PASS

This plug fits our inlet manifolds and Rover types with servo take off holes.

Also is the plug for cylinder head by pass tube hole when blanking off

$4.55
($3.10 USD ) In stock

MINI & MOKE CARBY MANIFOLD BLANKING PLUG- ORIGINAL TYPE - 122132

122132/ADP210- MINI & MOKE TWIN CARBY BLANKING PLUG

This is the manifold plug/bolt that is used on twin carby manifolds when the PCV setup etc is not used. This will bolt in place to stop any vacuum leaks.

$9.05
($6.17 USD ) In stock

MINI & MOKE COPPER WASHER- DOES SUMP PLUG/BLOCK/MANIFOLD PLUS MORE - AED172

AED172- MINI & MOKE COPPER WASHER- DOES SUMP PLUG/BLOCK/MANIFOLD PLUS MORE

Mini Copper Sump Drain Plug Washer, also will fit the oil transfer pipe block fitting (Pre 1992 Blocks). Outside diameter is 25.38mm, Inside diameter is 16.28mm & washer thickness is 1.5mm

$2.27
($1.55 USD ) In stock

MINI & MOKE BOOSTER FITTING FOR MANIFOLD- ORIGINAL TYPE - 12H1405

12H1405- Servo fitting for the booster outlet on twin carby mainfold

This is a fitting that screws into the twin carby manifold, it allows you to feed in your servo. this will suit the C-AHT770 single manifold too.

$22.68
($15.48 USD ) In stock

MINI & MOKE BOOSTER FITTING FOR MANIFOLD- AFTERMARKET TYPE - 12H1405MS

12H1405MS- MINI & MOKE BOOSTER FITTING FOR MANIFOLD- AFTERMARKET TYPE

Aftermarket union for fitting all mini inlet manifolds where a take off is required for your brake servo or emission valve on Cooper S cars.

$18.14
($12.37 USD ) In stock

Super charger kit to fit SC12 super charger (see item description) - AFF01

AFF01- SC12 Kits- DOES NOT include SC12 supercharger or HIF style SU

 

This is a super charger installing kit to fit the Toyota MR2 (SC12) super charger onto a mini. You will need to source a super charger and a HIF carby. (see description for what kit includes)

$1086.36
($741.25 USD ) In stock