Minisport

Rear Panels

Pricing:
Sort by:

MINI MK1 BOOT LID- LARGE FLAP TYPE - 28G110

28G110- Mini MK1 (early) boot lid- with large flap

MKI (850) boot/trunk lid is now back in production. These are such good reproductions that British Heritage are offering these units as "factory original". These are the 'large flap' 850 design and are (to the best of our knowledge) the only ones available. *Extra freight will apply to keep this safe*

$590.91
($396.80 USD ) In stock

MINI MK3/ROVER BOOT LID- NO FLAP TYPE - BMP339

BMP339- MK3/rover BOOT LID UP TO 1991

ROVER BOOT LID MK3 until '91 with holes for seal retaining clips

*Extra freight will apply to keep this safe*

$450.00 $417.27
($280.20 USD ) In stock

MINI NUMBER PLATE BRACKET REAR- LARGE TYPE - 14A6468

14A6468- NUMBER PLATE BRACKET REAR MK1 850 (larger type)

The MKI (850 sliding window) number plate panels are hinged at the top to swing out clear of the bumper when you open the boot lid.

$36.32
($24.39 USD ) In stock

MINI NUMBER PLATE FLAP HINGE- R/H - 14A6466

14A6466- NUMBER PLATE HINGE R/H MK1/2

The MKI & MKII number plate panels 14A6468 are hinged at the top to allow you to keep your boot open while you drive along, this keeps the numberplate visable at all times.

$22.68
($15.23 USD ) In stock

MINI NUMBER PLATE FLAP HINGE- L/H - 14A6467

14A6467- NUMBER PLATE HINGE L/H MK1/2

The MKI & MKII number plate panels 14A6468 are hinged at the top to allow you to keep your boot open while you drive along, this keeps the numberplate visable at all times.

$22.68
($15.23 USD ) In stock

MINI NUMBER PLATE FLAP HINGE SCREW - 211081

211081- MINI BOOT FLAP SCREW 3/16 (also can be used on Australian door strikers)

This is a boot flap screw that holds the boot flap hinge onto the car, there are 6 of these required per car. the thread is 3/16th of an Inch. these screws can be used on the australian door strikers HYA2805 (you will need to run a 3/16 tap)

$2.00
($1.34 USD ) In stock

Morris Mini rear back (round taillights) boot panel section- top to bottom - HMP441046

HMP441046- REAR PANEL COMPLETE WITH MK1 LAMP CONVERSION

Complete rear back panel section from roof to bumper valance with MK1/2 lamp holes, bootlid and backlight holes to fit all models from 1967 to 2000. This is a great repair section which can be cut to suit each individual car as it is very rare for the upper window section to be rotten. Please be aware that these back sections will require the english (large) rear window screens, these are readily available and should not cost more than $50.

**EXTRA FREIGHT/PACKAGING WILL BE REQUIRED**

$590.91
($396.80 USD ) In stock

MINI 'CLUBMAN' TYPE REAR PANEL COMPLETE (UK MK2 ON) - ALA6417

ALA6417- MINI 'CLUBMAN' TYPE REAR PANEL COMPLETE (UK MK2 ON)

MINI clubman Rear Body Panel whole rear section from roof to bumper valance with MK2 lamp holes, bootlid and backlight holes to fit al models from 1967 to 2000. Please note, these are made for the UK cars (mk2 onwards) these had a larger rear winsdcreen.

$590.91
($396.80 USD ) In stock

MINI 'CLUBMAN' TYPE REAR PANEL LOWER HALF - HMP441019

HMP441019- MINI 'CLUBMAN' TYPE REAR PANEL LOWER HALF

genuine rear lower back panel for leyland/rover on which goes up as far as lower edge of backlight seal ridge, most people use these to repair rust section on ALL models even Mk1&2

$500.00
($335.75 USD ) In stock

Mini rear back panel (below lights) includes hinge holes suits ALL models - HMP441009

HMP441009- REAR BACK PANEL LOWER REPAIR BELOW LIGHTS

Genuine repair panel which is about 2.52 high from bumper mounting seam and includes hinge holes and lower part of bootlid surround channel. Full width panel for any saloon.

$381.82
($256.39 USD ) In stock

Mini rear tail lamp gusset, Right hand - MS026R

MS026R- REAR LAMP GUSSET R/H MK1

R/H convertion panel from MK3 to MK1 this panel is made to weld into the larger rear lamp hole of MK3 from 1968 to end of production saloon cars back to the original MK1 smaller lamp for either that Retro look or body repairs. Also can be modified to fit Australian Leylands back to MK1 tail lights

$45.41
($30.49 USD ) In stock

Mini rear tail lamp gusset, left hand - MS026L

MS026L- REAR LAMP GUSSET L/H MK1

L/H convertion panel from MK3 to MK1 this panel is made to weld into the larger rear lamp hole of MK3 from 1968 to end of production saloon cars back to the original MK1 smaller lamp for either that Retro look or body repairs. Also can be modified to fit Australian Leylands back to MK1 tail lights

$45.41
($30.49 USD ) In stock

MINI BOOT FLOOR PANEL REAR SECTION ONLY ABOUT 9-10" DEEP - MS54

MS54- BOOT FLOOR PANEL REAR SECTION ONLY ABOUT 9-10" DEEP

This 9.5" rear section of the boot floor is ideal for collision or rust repair.

$83.64 $63.59
($42.70 USD ) In stock

MINI SPARE WHEEL WELL REPAIR SECTION. - CMS1010

This is a repair section for the spare wheel well only. Quite often you only have to repair the bottom of the wheel well- If so this is the panel for you. Easy weld in panel.

$122.73
($82.41 USD ) In stock

Mini boot side repair panel, Right hand side - MS24R

MS24R- BOOT SIDE REPAIR PANEL R/H

These small repair panels (MS24L for left, MS24R for right) are for the Mini boot floor area around the shock towers.

$35.45
($23.81 USD ) In stock