Minisport

Mini Hydrolastic rear traling arm bump stop (sold single) - 21A1520

BUMP STOP REAR HYDROLASTIC, LARGER RUBBER BUMP

Hydro rubber bump stop fits on rear trailing arm (original type)

Mini Hydrolastic rear trailing arm flat rebound rubber - 21A1517

21A1517- REBOUND BUFFER HYDROLASTIC, FLAT BUMP

This is the flatter type rear rebound rubber on hydrolastic cars, this one fits behind the rear trailing arm (behind the ball and cup) and stops it from hitting the sub-frame.  

MINI COMPETITION REAR BUMP STOPS- PAIR- HYDRO - C-AJJ3313

C-AJJ3313- MINI COMPETITION REAR BUMP STOPS- PAIR- HYDRO

Rear progressive bump stop kit for hydrolastic cars. Mounting brackets and rubbers.
The rearward pitch under hard acceleration can be minimized by the fitting of progressive bump stop kits. This also improves the car's handling when fully loaded. 

Mini Hydrolastic front top arm bump stop (sold single) - 21A1598

21A1598- BUMP STOP HYDROLASTIC FRONT

For Hydrolastic suspension cars, they were made with a 1/4" fixing hole but this needs elongating vertically to get the bump stop to sit properly on the upper arm which had different machine tolerances when manufactured

Pair of competition front top arm bump stops - C-AJJ4007

C-AJJ4007- BUMP STOP KIT, FRONT

Front progressive bump stop kit for hydrolastic cars. Mounting brackets and rubbers.
Improves car handling; especially under braking and when fully loaded.

Mini replacement bump stop for C-AJJ3313/4007 (sold single) - AHH7074

AHH7074- Mini replacement bump stop for competition bump stops

Bump stop as fitted by ST Works Abingdon to go on their bump stop kits C-AJJ3313/4007 for hydrolastic minis

MINI & MOKE DUAL BOLT BUMP STOP- DRY/RUBBER SUSPENSION - 2A4332

This is dual bolt bump stop as fitted to the dry/rubber suspension cars. This has the 2 threaded retaining bolts. This is mounted at the top of the subframe & stops the top arm from damaging the subframe. The single bolt type is FAM2764.

MINI & MOKE SINGLE BOLT BUMP STOP- DRY/RUBBER SUSPENSION - FAM2764

This is single bolt bump stop as fitted to the dry/rubber suspension cars. This has the single threaded retaining bolt. This is mounted at the top of the subframe & stops the top arm from damaging the subframe. The dual bolt type is 2A4332

MINI & MOKE FRONT BUMP STOP UNDER TOP ARM (REBOUND BUFFER) - AYA4033/2A4267MS

Fitted purely to prevent the top arm crashing in to the subframe on full droop (as when airborne), and stopping the suspension ball joint going bound in full droop. 2 required per car- fits all models (both hyrolastic & rubber suspension cars)

MINI & MOKE STRAIGHT LOWER CONTROL ARM BUSH- RUBBER - 2A4294

2A4294- MINI & MOKE STRAIGHT LOWER CONTROL ARM BUSH- RUBBER

This is a lower control arm bush that suits the pre 66 cars, the lower control arm bush is straight (not tapered) like the later ones. Sold single, 2 required per side, 4 required per car.

MINI & MOKE TAPER LOWER CONTROL ARM BUSH- RUBBER - 21A1882

21A1882- MINI & MOKE TAPER LOWER CONTROL ARM BUSH- RUBBER

As used on all leylands and most mini's from about 68 on, to be 100 percent sure if these will fit please inspect your lower control arms, if they taper in (where the bushes sit in the arm) then these are the ones you will need if not see 2A4294. 

MINI & MOKE TAPER LOWER CONTROL ARM BUSH- POLY - 21A1882MS

21A1882MS- MINI & MOKE TAPER LOWER CONTROL ARM BUSH- POLY

These are top hat type poly bushes that fit all lower arms with a twin taper bush hole. All minis later than 1965. Fitted with metal bush insert. Sold single, 2 required per side, 4 required per car.

MINI & MOKE TAPER LOWER CONTROL ARM BUSH SET OF 4- OFFSET- RACE - C-STR631

C-STR631- MINI & MOKE TAPER LOWER CONTROL ARM BUSH SET OF 4- OFFSET- RACE

When the castor and camber angles are changed or the geometry of the car is set up you will require these bushes. They are good for cars with up to 3.5 degrees of castor angle.

MINI & MOKE TAPER LOWER CONTROL ARM BUSH SET OF 4- OFFSET- FAST ROAD - C-STR632

C-STR632- MINI & MOKE TAPER LOWER CONTROL ARM BUSH SET OF 4- OFFSET- FAST ROAD

Made especially for use when geometry has been changed, such as fitting adjustable tie rods or lower arms, or on any cars with corrected castor angles. Set of 4 bushes

MINI & MOKE REAR SUBFRAME SUPPORT PIN- SOLD SINGLE - 21A1440MS

21A1440MS- MINI & MOKE REAR SUBFRAME SUPPORT PIN- SOLD SINGLE

This is the rear subframe support pin- uses 2A5818 bushes