Minisport

Suspension parts

This is your suspension page for everything you will require for your mini.

 

Pricing:
Sort by:

MINI & MOKE BALL JOINT NUT- HIGH TENSILE - FZN507

FZN507- MINI & MOKE BALL JOINT NUT

This is the nut for either your top or lower ball joint on either drum or disc brake cars.

$1.77
($1.22 USD ) In stock

MINI & MOKE BALL JOINT DUST COVER BOOT - BTA377

MINI & MOKE BALL JOINT DUST COVER BOOT

This is a dust cover/boot for either your top or lower ball joint on either drum or disc brake cars. 

$2.68
($1.84 USD ) In stock

MINI & MOKE BALL JOINT LOCKTAB - 2A4238

MINI & MOKE BALL JOINT LOCKTAB

This is the locktab that fits under the ball joint nut on the front of any mini, it suits either drum or disc brakes

$5.41
($3.72 USD ) In stock

MINI & MOKE BALL JOINT SHIM SET- PKT OF 6 - 2A4242

2A4242- Ball joint shim set (pack of 6)

Replacement ball joint shims, comprising of 2x 003"(.076MM) shims, 2x 005"(.127MM) and 2 x 010"(.254MM)

$6.32
($4.34 USD ) In stock

MINI & MOKE GREASE NIPPLE- BALL JOINT & REAR TRAILING ARMS - LN10051

LN10051- Ball joint bleed nipple for front hub & rear trailing arm (2 per hub)

Always check these grease nipples on your front hubs are working as they are very important. These two swivel pin grease nipples are the same, upper and lower. Also used on the rear radius arms

$4.00
($2.75 USD ) In stock

MINI GREASE NIPPLE TOP ARM (45 DEGREE ANGLE) - UHN445

UHN445- MINI GREASE NIPPLE TOP ARM (45 DEGREE ANGLE)

Angled grease nipple for the upper arm on the front suspension of all Minis, importantly lubricates the upper arm spindle which so often gets neglected so check yours out and make sure this nipple is working properly

$4.00
($2.75 USD ) In stock

MINI & MOKE BALL JOINT KIT- PAIR- MS - GSJ166MS

GSJ166MS- Mini & Moke Ball joint kit (upper & Lower) fits ALL Australian minis *SOLD AS A PAIR*

Mini & Moke Ball joint kit (upper & Lower) fits ALL Australian minis, if your ball joints look like the ones in the picture then these are the ones you need! *SOLD AS A PAIR*

$23.64
($16.25 USD ) In stock

MINI & MOKE BALL JOINT KIT- PAIR- GENUINE - GSJ166GEN

GSJ166GEN- MINI & MOKE BALL JOINT KIT- PAIR- GENUINE

These are the genuine Unipart ball joint kit as fitted to Minis & Mokes (upper & Lower) fits ALL Australian minis, if your ball joints look like the ones in the picture then these are the ones you need! *SOLD AS A PAIR*

$40.91
($28.13 USD ) In stock

MINI & MOKE ROLL CENTRE ADJUSTERS - GSJ166ROLL

GSJ166ROLL- MINI & MOKE ROLL CENTRE ADJUSTERS *PAIR*

Roll centre adjusters replace the bottom ball joints on the Mini. They are used to stop increased roll resulting from lowered suspension. These adjusters can be used on all models of Classic Mini from 1959-2001. *SOLD AS A PAIR*

$127.23
($87.49 USD ) In stock

MINI & MOKE THICK FLAT WASHER FOR TIE BAR (SOLD SINGLE - 2 PER CAR)) - PWZ207

PWZ207- Mini thick washer, for tie bar

This flat thick waher sits against the cup washer (2A4328) that stops the tie bar from pulling out of the subframe.

$2.68
($1.84 USD ) In stock

MINI & MOKE THICK CUP WASHER FOR TIE BAR (SOLD SINGLE - 2 PER CAR)) - 2A4328

2A4328- Mini cup washer for tie bar

This cup washer sits against the tie bar suspension rubber, you also require the thick washer aswell (PWZ207)

$2.68
($1.84 USD ) In stock

MINI & MOKE ADJUSTABLE TIE BAR KIT- HEAVY DUTY - 21A1091

Pair of mini & moke adjustable front tie-rods bars. When you change the length of the lower control arm to attain the desired degree of camber, the caster also changes. To reset it you must be able to change the length of the tie-rods. Our special adjustable tie rods are almost twice the diameter of the stock version and are far less likely to bend.

$77.27 $62.73
($43.13 USD ) In stock

MINI & MOKE TIE BAR KIT WITH BUSH KIT & FIXINGS - 21A1092

21A1092- TIE BAR KIT 21A1091 WITH C-STR627 BUSH KIT & FIXINGS

Adjustable tie-rod kit with rubber bushes and all bolts,nuts and washers required. This is one car set.

When you change the length of the lower control arm to attain the desired degree of camber, the caster also changes. To reset it you must be able to change the length of the tie-rods. Our special adjustable tie rods are almost twice the diameter of the stock version and are far less likely to bend. Remember, in addition to controlling caster, these tie-rods also control stability under braking! Our own brand have a hexagonal cut on the rod for easy adjustment. 

$86.36
($59.39 USD ) In stock

MINI & MOKE ROSE JOINTED K.A.D TIE BARS- OFF ROAD ONLY - 1012265

1012265- KAD Insitu Adjustable Tie Rods (PAIR)

These have been designed for hard competition use, billet steel brackets are used at both ends as the cheaper to produce fabricated steel brackets used by others have been known to fail with disastrous consequences in competition usage.

The tie rod itself is made from manganese moly steel which is incredibly stiff without having the excess weight penalty of some of the more agricultural tie rods sold elsewhere. The bar is left and right hand threaded which means castor adjustment can be made quickly and precisely without removal from the car.

$409.09
($281.31 USD ) In stock

Mini 1.5 negative lower control arms (pair) - C-AJJ3364

C-AJJ3364

Sold in pairs only.

These arms will give an extra 1.5 degrees extra negative camber to what the standard lower contol arms give on your car. If you want adjustable see C-AJJ3360

$204.55
($140.66 USD ) In stock